Bedienungsanleitung Yamaha yrs 1000 (Seite 32 von 684) (Englisch)

419719

Zoom out

Zoom in

Vorherige Seite

1/684

Nächste Seite

AUTO SETUP (IntelliBeam)

30 En

The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening

environment. Follow the procedure below to connect the IntelliBeam microphone to this unit and make sure that the

IntelliBeam microphone is placed in a proper location and that there are no large obstacles between the IntelliBeam

microphone and the walls in your listening room.

• After you have completed the AUTO SETUP procedure, be sure to disconnect the IntelliBeam microphone.

• The IntelliBeam microphone is sensitive to heat.

– Keep it away from direct sunlight.

– Do not place it on top of this unit.

• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate sound optimization.

• An error may occur during the AUTO SETUP procedure if the IntelliBeam microphone is not properly placed in your listening room.

To avoid the possibility of an error:

– Do not place the IntelliBeam microphone to the extreme right or left from the center of this unit.

– Do not place the IntelliBeam microphone within 1.8 m (6.0 ft) from the front of this unit.

– Do not place the IntelliBeam microphone more than 1 m (3.3 ft) upper or lower from the center height of this unit.

• Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects

obstruct the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the

walls.

• The best possible results are achieved if the IntelliBeam microphone is placed at the same height as your ears would be when you are

seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the

sound beam output levels using MANUAL SETUP (see page 53) once the AUTO SETUP procedure is completed.

1 Press STANDBY/ON to turn off the power of

this unit.

2 Connect the supplied IntelliBeam

microphone to the INTELLIBEAM MIC jack

underside of the front panel.

3 Place the IntelliBeam microphone on a flat

level surface more than 1.8 m (6.0 ft) from the

front of the unit and within 1 m (3.3 ft) upper

or lower from the center height of the unit

with the IntelliBeam microphone facing

upward at your normal listening position.

Be sure to place the IntelliBeam microphone on an

imaginary center line drawn from this unit.

You may want to use the supplied cardboard microphone

stand to affix the IntelliBeam microphone at the same height

as your ears would be when you are seated in your listening

position.

Installing the IntelliBeam microphone

Notes

STANDBY/ON

Front panel

Remote control

Note

IntelliBeam

microphone

More than

1.8 m (6.0 ft)

Within 1 m (3.3 ft)

upper or lower

from the center

height

Cardboard

microphone stand

Sofa

Upper bound

position of the

microphone

Lower bound

position of the

microphone

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha yrs 1000 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha yrs 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info