Bedienungsanleitung Yamaha YRS-2100 (Seite 2 von 2) (Englisch)

516969

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Installation Connection Settings Playback

Carry out AUTO SETUP for appropriate surround effects

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud

test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the

AUTO SETUP procedure is in progress.

Set the IntelliBeam microphone at your normal listening position.

Assemble the stand and place the IntelliBeam microphone on top of it horizontally as shown below.

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be

when you are seated.

Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects obstruct the

path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the walls.

Press key on the remote control.

The power of this unit turns on.

Turn on the power of your TV and select YRS-2100/YRS-1100 as the video input on your TV.

If you connected the video pin cable to TV Video In 1, as shown in the connection diagram, select video input 1 on the TV.

If no menu appears, make sure the video pin cable is connected correctly.

123 45

IntelliBeam microphone

Upper limit

Center height of

this unit

Within 1 m (3.3 ft)

Listening

position

Cardboard microphone

stand

1.8 m (6.0 ft)

or more

Lower limit

Center line

IntelliBeam

microphone

Cardboard

microphone

stand

YRS-2100

Push [SETUP] to

begin SETUP MENU.

You can select the language described in the menu screen. → Press and hold SETUP key until

the “LANGUAGE SETUP” menu appears. → Press U/V key to select the desired language and

then press ENTER key. → Press SETUP key again.

yHint

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack on the front panel.

Make sure that your listening room is as quiet as possible.

For accurate measurement, turn off air conditioner or other devices that make noises.

Leave the room after the next procedure. The best setting may not be done if you are in the room. When leaving the room, bring this Quick

Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside the room during the AUTO SETUP procedure.

To cancel the AUTO SETUP procedure after it is started, press RETURN key.

Press ENTER key to start the AUTO SETUP procedure and then leave the room within 10 seconds.

The screen changes as each measurement is carried out.

When the process is complete, a bell will sound and the

results will be displayed on the TV.

If “ENVIRONMENT CHECK : Failure” (“Error Code: E-1” etc.

is displayed in the front panel display) is displayed, see page

13 of the Owner’s Manual and run the measurement

process again.

The results displayed depend on the position of the YRS-

2100/YRS-1100.

If you hear a buzzer sound and an error message

appears on the TV, look for a solution in “Error messages

for AUTO SETUP” on page 14 of the Owner’s Manual.

Then press RETURN key to run the measurement

process again.

Press ENTER key.

The measurement result is saved.

Disconnect the IntelliBeam microphone.

The initial screen appears. Keep the IntelliBeam microphone in a safe

place. The settings are automatically saved in the system memory.

IntelliBeam microphone (supplied)

Cardboard microphone stand

(supplied)

AUTO SETUPSETUP

(PREPARATION & CHECK)

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from SoundPro-

jector. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

Start Setup?

TV screen

Front panel display

yHint

Will begin in 10 sec.

Please leave the room.

---------

AUTO SETUP START

[RETURN]:Cancel

MEASUREMENT COMPLETE.

BEAM MODE :5Beam/Plus2

SUBWOOFER :Yes

[ENTER]:Save set-up.

[RETURN]:Do

not save

set-up.

XXXXXXXXSHOW RESULTXXXXXXXXXX

Start in 10sec

5Beam /SWF:RDY

About 3

minutes

later

yHint

AUTO SETUP COMPLETE

Please remove the MIC

from Sound Projector

and the listening position.

Setup Finish.

Installation Connection Settings Playback

Playing back

Play back the supplied demonstration DVD, and confirm the exact connection and settings.

Then, have fun for playback!

For detailed operation, see the supplied Owner’s Manual.

Press key to turn on this unit.

Turn on your TV and Blu-ray disc player connected to this

unit.

Press HDMI1-3 to select the Blu-ray disc player as the input

source.

Press TV key to select the TV as the input source.

Set the input source of TV to HDMI input 1.

Play back the supplied demonstration DVD.

Refer to “Using the supplied demonstration DVD”. (See Owner’s Manual on page

53.)

Press VOLUME +/- key to adjust the volume.

Use TV remote control to mute the sound from TV.

Press SURROUND key and then the CINEMA DSP keys to

set your sound preferences.

When this unit does not play back, check the following

The connection between this unit and Blu-ray disc player.

The audio output settings of Blu-ray disc player is set to digital sound output.

The input of TV is selected exactly.

HDMI1

Input source name

yHint

HDMI control function

You can use the TV remote control to operate this unit if your TV supports the HDMI control function. See the page 19 of Owner’s Manual about

settings.

yHint

Yamaha YRS-2100 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha YRS-2100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info