The following screen appears on the TV. Leave the room
within 10 seconds before the AUTO SETUP procedure
starts.
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is completed, the
following screen appears on the TV.
If “ENVIRONMENT CHECK (FAILED) is displayed, see page
42 in the Owner’s Manual and then run the procedure again.
y Hint
• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears
on the screen. In this case, see “Error messages for AUTO
SETUP” on page 43 in the Owner’s Manual and then follow
the instructions. To start the AUTO SETUP procedure once
again, press RETURN.
Press ENTER.
The following screen appears on the TV for 2 seconds and
then the menu screen disappears from the TV.
Disconnect the IntelliBeam
microphone.
The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.
Enjoying surround sound
Carry out the AUTO SETUP to adjust the settings that best match your
listening environment
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
Press STANDBY/ON on the
remote control.
The power of this unit turns on.
Before operations, insert batteries into the remote control
(see page 32 in the Owner’s Manual).
If necessary, adjust the volume level of this unit.
If you have connected the subwoofer, set the volume and
crossover/high cut frequency. Refer to the note on page
38 in the Owner’s Manual.
Check the digital signal being output at this unit.
The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they switch
according to the channel composition of the corresponding input source. If the sound is output from your TV
speakers, mute the volume on your TV. For details about digital audio input signals, see page 58 in the Owner’s
Manual.
Press VOLUME +/
-
on the remote control to adjust the volume
level of this unit.
Press one of the beam mode buttons on the remote control
to select the desired beam mode.
Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see page 56 in the Owner’s Manual.
To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,
sound beams, etc., see “MANUAL SETUP” on page 76 in the Owner’s Manual.
AUTOSETUPSTART
Willbeginin10sec
Pleaseleavetheroom
**--------
[RETURN]:Cancel
10
Enjoying TV in surround sound
3
SHOWRESULT
MEASUREMENTCOMPLETE
BEAMMODE:5BEAM
SUBWOOFER:NOTAPPLICABLE
[ENTER]:Saveset-up
[RETURN]:Donotsaveset-up
AUTOSETUPCOMPLETE
PleaseremovetheMICfrom
theYSPandthelistening
position.
TV/AV
YSP
ENTER
ENTRY
A-E
ENHANCER
DISPLAYRETURN
MENU
TV/AV
YSP
ENTER
ENTRY
A-E
ENHANCER
DISPLAYRETURN
MENU
Select the TV channel using the
remote control supplied with
your TV.
Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
Press TV on the remote control
of this unit.
This unit switches to the TV playback mode.
More than 1.8 m (6.0 ft)
Within 1 m
(3.3 ft)
IntelliBeam
microphone
Cardboard
microphone
stand
Listening
position
Place the IntelliBeam microphone on
the extended center line of this unit
and 1.8 m (6.0 ft) or more away from
it. Also, make sure place the
IntelliBeam microphone within 1 m
(3.3 ft) upper or lower from the center
height of this unit.
IntelliBeam
microphone
Center line
Carry out the AUTO SETUP (IntelliBeam)
INTELLIBEAM MIC
1234
Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
be when you are seated.
IntelliBeam microphone (supplied)
Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC
jack on the front panel.
You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam
microphone on top of it as shown below.
MUTETV INPUTTV MUTE
VOLUMECHTV VOL
Enjoying DVDs in surround sound
Select the DVD video input on
your TV.
Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
1) Press DVD on the remote
control of this unit.
This unit switches to the DVD playback mode.
2)
Play back the supplied demonstration
DVD on the DVD player.
Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
Press and hold AUTO SETUP for
more than 2 seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video
pin cable (see the connection example on the front page).
Check the following points.
About the IntelliBeam microphone
• Is the microphone placed on an imaginary center line drawn
from this unit?
• Is the microphone placed within 1 m (3.3 ft) upper or lower
from the center height of this unit?
• Is the microphone placed more than 1.8 m (6.0 ft) from the
front of this unit?
About the room environment
• Is your listening room kept as quiet as possible?
Prepare to leave the room.
The best setting may not be done if you are in the room.
Prepare to leave the room in 10 seconds after pressing
ENTER in step 10.
y Hint
• When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes about 3 minutes.
• To cancel the AUTO SETUP procedure after it is started,
press RETURN.
Turn on the power of your TV.
Select the appropriate video
input on your TV.
If the OSD video pin cable is connected to the video input 1
on the TV as shown in the connection example, switch the
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yamaha YSP-4000 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
