Carry out the AUTO SETUP to adjust the settings that best match your listening
environment.
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player/recorder, refer to the owner’s manual supplied with each component.
Assemble the cardboard microphone stand.
Place the IntelliBeam microphone on top of the cardboard microphone stand as shown below.
Carry out the AUTO SETUP (IntelliBeam)
3
Enjoying surround sound
4
y Hint
y Hint
Continued from the front
1
Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack
on the front panel.
2
Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
be when you are seated.
3
Press STANDBY/ON on the remote control.
The power of this unit turns on.
Before operations, insert batteries into the remote
control (see page 27 in the Owner’s Manual).
If necessary, adjust the volume level of this unit.
If you have connected the subwoofer, set the
volume and crossover/high cut frequency. Refer
to the notes on page 33 in the Owner’s Manual.
4
Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
7
Press ENTER to start the AUTO
SETUP procedure, and then leave
the room within 10 seconds.
The following screen appears on the TV. Leave the room within
10 seconds before the AUTO SETUP procedure starts.
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is completed, the following
screen appears on the TV.
If “ENVIRONMENT CHECK (FAILED)” is displayed, see page
37 in the Owner’s Manual and then run the procedure again.
• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears
on the screen. In this case, see “Error messages for AUTO
SETUP” on page 38 in the Owner’s Manual and then follow
the instructions. To start the AUTO SETUP procedure once
again, press RETURN.
11
Press and hold AUTO SETUP for
more than 2 seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video pin
cable (see the connection example on the front page).
8
Prepare to leave the room.
The best setting may not be done if you are in the room.
Prepare to leave the room in 10 seconds after pressing ENTER
in step 11.
• When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes about 3 minutes.
• To cancel the AUTO SETUP procedure after it is started,
press RETURN.
10
Disconnect the IntelliBeam
microphone.
The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
13
Check the following points.
About the IntelliBeam microphone
• Is the microphone placed on an imaginary center line drawn
from this unit?
• Is the microphone placed within 1 m (3.3 ft) upper or lower
from the center height of this unit?
• Is the microphone placed more than 1.8 m (6.0 ft) from the
front of this unit?
About the room environment
• Is your listening room kept as quiet as possible?
9
Press ENTER.
The following screen appears on the TV for 2 seconds and then
the menu screen disappears from the TV.
12
Select the DVD video input on
your TV.
1
Check the multi-channel digital signal being output at this unit.
The MULTI indicator (see page 8 in the Owner’s Manual) is lit in the front panel display. If the sound is output
from your TV speakers, mute the volume on your TV. For details about digital audio input signals, see page 43 in
the Owner’s Manual.
4
Press one of the beam mode buttons on the remote control to
select the desired beam mode.
Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see pages 45 to 47 and 51 to 53 in the Owner’s Manual.
6
Press VOLUME +/– on the remote control to adjust the
volume level of this unit.
5
Select the TV channel using the
remote control supplied with your TV.
Mute the volume on the TV.
1
Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
2
Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
2
1) Press DVD on the remote
control of this unit.
This unit switches to the DVD playback mode.
2)
Play back the supplied demonstration
DVD on the DVD player/recorder.
3
Press TV on the remote control of
this unit.
This unit switches to the TV playback mode.
3
Turn on the power of your TV.
5
Select the appropriate video input
on your TV.
If the OSD video pin cable is connected to the video input 1 on
the TV as shown in the connection example, switch the video
input to “1”.
6
IntelliBeam microphone (supplied)
Cardboard microphone stand (supplied)
1243
Place the IntelliBeam microphone on the
extended center line of this unit and 1.8 m (6.0 ft)
or more away from it. Also, make sure place the
IntelliBeam microphone within 1 m (3.3 ft) upper
or lower from the center height of this unit.
IntelliBeam
microphone
Center height of
this unit
IntelliBeam
microphone
Cardboard
microphone stand
More than 1.8 m (6.0 ft)
Upper bound
position of the
microphone
Within 1 m (3.3 ft)
Within 1 m (3.3 ft)
Listening
position
Lower bound position
of the microphone
Center line
Cardboard
microphone
stand
Enjoying DVDs in surround soundEnjoying TV in surround sound
MULTI indicator
To fine-tune the listening environment parameters manually or make advanced settings for speaker positions, sound
beams, etc., see “MANUAL SETUP” on page 58 in the Owner’s Manual.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yamaha YSP-600 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
