Bedienungsanleitung Yamaha YST-SW105 (Seite 11 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

559186

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

E-9

If the source being played is stopped and the input signal is

cut off for 7 to 8 minutes, the subwoofer automatically

switches to the standby mode. (When the subwoofer

switches to the standby mode by the automatic power-

switching function, the power indicator lights up in red.)

When you play a source again, the power of the subwoofer

turns on automatically by sensing audio signals input to the

subwoofer.

This function operates by sensing a certain level of low

frequency input signal. Usually set the AUTO STANDBY

switch to the LOW position. However, if the power is not

switched to ON or STANDBY smoothly, set the switch to the

HIGH position. In the HIGH position, the power will turn on

even with a low level of input signal. But please be aware

that the subwoofer may not switch to the standby mode

when there is an extremely low input signal.

* The power might turn on unexpectedly by sensing noise

from other appliances. If that occurs, set the AUTO

STANDBY switch to the OFF position and use the

STANDBY/ON button to switch the power between ON

and STANDBY manually.

* This function detects the low-frequency components

below 200 Hz of the input signals (i.e., the explosion in

the action movie, the sound of the bass guitar or the bass

drum, etc.).

* The minutes required to switch the subwoofer to the

standby mode might change by sensing noise from other

appliances.

This function is available only when the power of the

subwoofer is on (by pressing the STANDBY/ON button).

¤ OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the main speakers.

Signals from the INPUT1 terminals ($) are sent to

these terminals.

(Refer to “CONNECTIONS” for details.)

# INPUT2 terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

‹ AUTO STANDBY (HIGH/LOW/OFF) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described below. If you do not need this

function, leave this switch in the OFF position.

* Make sure to change the setting of this switch only

when the subwoofer is in the standby mode. (The

power indicator does not light.)

$ INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

(Refer to “CONNECTIONS” for details.)

AUTOMATIC POWER-SWITCHING FUNCTION

› POWER switch

Normally, set this switch to the ON position to use the

subwoofer. In this state, you can turn on the subwoofer

or turn the subwoofer into the standby mode by

pressing the STANDBY/ON (Ÿ) button. Set this switch

to the OFF position to completely cut off the

subwoofer’s power supply from the AC line.

% VOLTAGE SELECTOR switch

(China and General models only)

If the preset setting of the switch is incorrect, set the

switch to the proper voltage (110V, 120V, 220V or

240V) of your area.

Consult your dealer if you are unsure of the correct

setting.

WARNING

Be sure to unplug the subwoofer before setting the

VOLTAGE SELECTOR switch correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha YST-SW105 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info