Bedienungsanleitung Yardforce SA800PRO (Seite 22 von 33) (Englisch)

733774

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

42 43

Setting the mowing height

The mower’s mowing height can be set between 20 and 60 mm with 5 cutting heights. If

the grass is higher than 60 mm, it will be necessary to mow the grass using a standard

lawnmower. Otherwise, the grass will cause too great a load for the mower’s blades and thus

lead to unsatisfactory mowing. Do not adjust the cutting height during mowing.

1. Press the main isolation switch to turn off the mower.

2. Open the top cover.

3. Rotate the mowing height selector to adjust the mowing height.

• It is recommended to begin with mowing by setting the mowing height to 60 mm (by

setting the selector to MIN) and then gradually lowering the mowing height until you get

the desired grass height.

4. Close the top cover after the adjustment.

Note: The mower can cut on wet grass. However this will lead to clumps of grass

forming under the mower which means more frequent cleaning of the mower is

necessary.

Starting and stopping the mower

Starting the mower

1. Make sure the mower is sufciently charged.

2. Press the main isolation switch to turn on the mower.

3. Press the STOP button to open the control panel cover.

4. If a PIN is set, enter the PIN with the number keys on the display .

5. Press the START button in the control menu.

6. Close the control panel cover. The mower will start mowing.

Note: The mower can be programmed to automatically start mowing at specific times

and on specific days in a week. See the section: Programming the mower.

Stopping the mower

• Press the STOP button(2) to immediately stop the mower.

Note: Once the STOP button is activated, the control panel cover will open and the

mower will wait for further commands. The mower will not start to work until the control

panel cover is closed.

Messages on the display during operation

While mowing, the display will show the operating status of the mower.

Information includes the current date and time, battery level, boundary cable signal

(S1 or S2) and operation status message (see below).

Message Description

Running

The mower is working. When the blade disc starts to rotate, the

blade disc icon (

) will show and ash on the display.

Home

The mower is in the process of returning to the charging sta-

tion.

Low voltage

The battery power is low and the mower will return to the

charging station.

Charging The mower is being charged.

No signal There is no boundary cable signal.

Outside The mower has moved outside the mowing zone.

Trapped

The obstacle sensor gives continuous alert for more than 10

seconds. The mower has stopped for safety reasons.

Pit

The obstacle sensor has triggered more than 10 times in one

minute. The mower has stopped for safety reasons.

Slope

The mower has encountered a steep slope which it cannot

overcome.

Lifted

The mower has either been lifted up or risen up over an obsta-

cle.

Error Incorrect PIN passcode is entered.

OPERATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce SA800PRO Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info