Bedienungsanleitung Yardforce SA800PRO (Seite 30 von 33) (Englisch)

733774

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

58 59

Cleaning the underside

Ensure the main power switch (11) is in OFF position. Wear protective gloves. Turn the

Robomower onto its side to expose its underside. Clean the blade disc and frame using a soft

brush or damp cloth. Rotate the blade disc to make sure that it moves freely, and check that the

blades can turn on their pivots and no grass is obstructing them.

Clean the contact pins and the charging strips

Using wire wool, metal cleaner or very ne grade emery paper, clean the contact pins and

the charging strips on your mower and charging station. Remove any debris, leaves or grass

clippings around the contact pins and charging strips to ensure efcient charging.

Reversing or replacing the blades

WARNING!

Ensure the Robomower is completely shut off before cleaning, adjusting or replacing

the blades. Always wear protective gloves.

WARNING!

To ensure maximum cutting efciency and safety, always use recommended

replacement blades and blade mounting parts when replacing.

Your Robomower has three blades xed to the blade disk.

Unless damaged by hard obstacles, these blades can last for up to ve months with everyday

use.

Weekly inspection of the blades and the xing screws is required. Note that the blades are

double-edged. Once the rst side is blunt, loosen the xing screw. Turn the blade upside-

down and x it again with the xing screw. After tightening the xing screw, verify that the

blade can rotate freely around the screw.

A set of spare blades is included with the Robomower. More are available from customer

support. The blade's spare part number is 846210.

Only use original spare parts. For best performance and avoiding imbalance, always turn or

replace all three blades at the same time.

Replacing the battery

While the actual battery life will depend on usage and environmental factors, the typical

service life is several years. Spare batteries are available from customer support. To

replace the battery, please follow the instructions below.

1) Ensure the main power switch (11) is turned OFF. Clean the underside as instructed.

2) Set the Robomower to the lowest cutting height.

3) Turn the mower upside-down. Remove the 5 screws xing the battery compartment's lid.

Note one screw is partially covered by the blade protector and is only accessible through

a service hole.

4) Pull out the battery and disconnect it from the Robomower.

5) Carefully clean the lid and the edge of the battery compartment. Debris may allow

excessive water to enter the battery compartment, causing major damage to the device.

6) Connect and insert the replacement battery, close the compartment and x the lid with 5

screws. Do not turn on the Robomower before placing it back on its wheels - beware of

sharp blades!

CLEANING/MAINTENANCE CLEANING/MAINTENANCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce SA800PRO Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info