Bedienungsanleitung Yardforce Y0GWB31EW00 (Seite 17 von 24) (Englisch)

734895

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Check and Clean Inlet Screen

Examine garden hose inlet screen. Clean if it is clogged or

replace if it is torn. Please call help line 1-866-902-9690 for

new purchase.

Check High Pressure Hose

High pressure hoses can develop leaks from wear, kinking,

or abuse. Inspect hose before each use. Check for cuts,

leaks, abrasions, bulging of cover, or damage or movement

of couplings. If any of these conditions exist, replace hose

immediately. Or call at 1-866-902-9690 for help or new

purchase.

WARNING The high pressure stream of water that this

pressure washer produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• Never repair a high pressure hose. Replace it.

• Replace with hose MUST equal or exceed the maximum

pressure rating of your pressure washer.

Check Detergent Siphoning Tube

Examine the detergent tube (equipped at the bottom of

detergent tank) and clean if clogged. One end of the tube

pump. Examine the tube for leaks or tears.

Replace detergent tank or tube if either is damaged. Or call

at 1-866-902-9690 for help or new purchase.

Check Spray Gun, Spray Wand and Nozzles

Examine hose connection to spray gun connected with

spray wand and make sure it is secure. Test trigger by

pressing it and make sure it springs back into place when

you release it. Engage trigger lock in UP position and test

trigger. You should not be able to squeeze the trigger.

Replace spray gun immediately if it fails any of these tests.

Purge Pump of Air and Contaminants

To remove air from the pump, follow these steps:

• Set up the pressure washer as described in the

"Assembly" section and connect the water supply.

• Squeeze the trigger on the gun and hold until a steady

stream of water appears.

To remove contaminants from the pump, follow these

steps:

• Set up the pressure washer as described in the

"Assembly" section and connect water supply.

• Remove the nozzle from the spray wand .

• Start the engine according to instructions in "How To Use

Your Pressure Washer" section.

• Squeeze the trigger on the gun and hold.

• When the water supply is steady and constant, engage

the trigger lock and install the nozzle.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure. The

principal cause of excessive pump pressure is a nozzle

clogged or restricted with foreign materials, such as dirt,

etc. To correct the problem, immediately clean the nozzle by

needle provided with your pressure washer and follow these

instructions:

2. ALWAYS point spray gun at a safety direction, release

trigger lock and squeeze spray gun trigger to release

retained high water pressure.

3. Remove the nozzle from the end of the spray wand.

4. Use the needle to free any foreign material clogging or

restricting the nozzle.

5. Using a garden hose, remove additional debris by back

flushing water through the nozzle. Back flush between

30 to 60 seconds.

6. Reinstall the nozzle to the wand with spray gun.

7. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

8. Start engine following instructions “How to Start Your

Pressure Washer”.

9. Test pressure washer by operating with each quick-

connect nozzle.

O-Ring Maintenance

Through the normal operation of your pressure washer,

o-rings keep the connections of the hoses and spray gun

tight and leak-free. They may become worn or damaged

with use.

You can purchase the replacement o-rings at the pressure

washer help line 1-866-902-9690.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce Y0GWB31EW00 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info