Bedienungsanleitung Yardforce Y0GWC3200R0 (Seite 18 von 31) (Englisch)

734892

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

WARNING The high pressure stream of water that this

pressure washer produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER repair leaking connections with sealant of any

kind. replace o-ring or seal.

ENGINE MAINTENANCE

WARNING Unintentional sparking could cause re or

electric shock resulting in death or

serious injury.

WHEN ADJUSTING OR MAKING REPAIRSTOYOUR

PRESSUREWASHER

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DONOT check for spark with spark plug removed.

Oil

Oil Recommendations

We recommend the use of CRAFTSMAN Warranty Certied

oils for best performance. Other high-quality detergent oils

are acceptable if classified for service SF, SG, SH, SJ or

higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

* Above 80°F (27°C) the use of 10W30 may cause

increased oil consumption. Check oil level more

frequently.

Checking Oil Level.

1. Make sure pressure washer is on a level surface.

2. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and check oil

level.

3. Verify oil is at FULL mark (top hole) on dipstick. Replace

and tighten dipstick.

Adding Oil.

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking O Level.

3. If needed, slowly pour oil into oil ll opening to the FULL

mark (top hole) on dipstick. DO NOT overll.

NOTICE

Oil level should be checked prior to each use or at

least every 5 hours of operation. Keep oil level

maintained.

Overfilling with oil could cause the engine to not start, or

hard starting.

• DO NOT overll.

• If over the FULL mark on dipstick, drain oil to reduce oil

level to FULL mark on dipstick.

Changing Oil

If you are using your pressure washer under extremely dirty

or dusty conditions, or in extremely hot weather, change oil

more often.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change oil while engine is still warm from running, as

follows:

1. Drain fuel tank by running pressure washer until fuel tank

is empty.

2. Disconnect spark plug wire and keep it away from the

spark plug.

3. Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tip your pressure washer to drain oil from the oil ll into

a suitable container making sure you tip your unit away

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce Y0GWC3200R0 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info