Bedienungsanleitung Yaesu ft-897D (Seite 26 von 76) (Englisch)

36023

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 24 FT-897D OPERATING MANUAL

LOCKING FRONT PANEL CONTROLS

The front panel LOCK button allows you to disable the DIAL

and/or the front panel controls.

RECEIVER ACCESSORIES

BATT- A

BATT- B

BAND

MODE

CLARAF

LOCK

PHONE

MIC

SQL

/RF

MEM/VFO CH

DWN UP

V/M

DSP

LOCK

In the transceiver’s default configuration, pressing the LOCK

button disables just the DIAL, while the other keys and

switches are unaffected.

To lock out the remainder of the controls and the MEM/

VFO CH knob, use Menu Mode No-054

[

LOCK MODE

]

;

1. Press and hold in the

[

]

key for one second to enter the

Menu mode.

2. Rotate the MEM/VFO CH knob so as to recall No-054

[

LOCK MODE

]

3. Rotate the DIAL to select the desired configuration:

DIAL: Locks DIAL knob only.

FREQ: Locks front panel keys and knobs related to fre-

quency control (such as BAND

(

DWN

)

and

BAND

(

)

key,

[

](

A/B

)

key., etc.)

PANEL: Locks all front panel keys and knobs (except

POWER and LOCK keys)

ALL: Locks all front panel keys and knobs (except

POWER and LOCK keys) and microphone

keys.

4. When you have made your selection, Press and hold in

the

[

]

key for one second to save the new setting and

exit to normal operation.

When the controls are locked out, press the LOCK button

once more to release them to normal operation.

CLARIFIER

(

RECEIVER INCREMENTAL TUNING

)

The Clarifier (RIT) allows you to set an offset of up to ±9.99

kHz of the receive frequency relative to your transmit fre-

quency. To achieve a wider offset than this, you may use the

“Split” operating mode, described later.

1. Press the CLAR/IF SHIFT button momentarily to acti-

vate the Clarifier function.

2. Turn the CLAR knob, which allows the receiver fre-

quency to be varied over a range of ±9.99 kHz.

3. When the receiving frequency is

higher than transmit frequency, the

“ (within 1 kHz)” or “ (exceed 1

kHz)” icon will appear at the right

of the frequency display. Similarly,

when the receiving frequency is

lower than transmit frequency, the

“ (within 1 kHz)” or “ (exceed 1

kHz)” icon will appear at the right

of the frequency display. When the

receiving frequency is equal to trans-

mit frequency (Clarifier offset is

zero) while the Clarifier is activated,

the “–” icon will appear at the right

of the frequency display.

4. To turn the Clarifier off, again press

the CLAR/IF SHIFT button mo-

mentarily. When you turn the Clari-

fier back on, the offset previously

stored will still be applied.

5. To reset the Clarifier offset to zero, turn the Clarifier off,

then turn the DIAL by any amount. The Clarifier will

reset to zero after the first “step” of the DIAL.

1) If you leave the Clarifier on, moving the DIAL

will not cause the offset to be cancelled.

2) You may change the knob that controls the

Clarifier offset from the DIAL to the MEM/VFO

CH knob via Menu Mode No-021

[

CLAR DIAL SEL

]

[

TX<RX

(

within 1 kHz

)]

[

TX=RX

(

Simplex

)]

[

TX>RX

(

within 1 kHz

)]

[

TX>RX

(

exceed 1 kHz

)]

BATT- A

BATT- B

BAND

MODE

CLARAF

LOCK

PHONE

MIC

SQL

/RF

MEM/VFO CH

DWN UP

V/M

DSP

CLARCLAR/IF SHIFT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu ft-897D Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info