Bedienungsanleitung Yeoman CL Electric Range (Seite 18 von 32) (Englisch)

813336

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Servicing Instructions

1. Fault Finding

No illumination or uneven lighting:

1.1 First change the BS1362 13A fuse for one known to work.

If the appliance still does not work, check the socket by

plugging in a working appliance. If this too fails to operate,

call in a competent electrician to check the socket.

1.2 One or more of the LED boards may need replacing. This

must be undertaken by a suitably qualified person (see

Servicing Requirements).

Illumination but no heat:

1.3 The safety cut-out may have operated to protect against

overheating (see User Instructions, Section 2). Ensure

the air inlet and outlet grilles are free of dust or any other

obstruction.

1.4 The thermostat control may be set too low. Increase the

setting by pressing the thermostat button on the remote

control until the heater turns on.

Remote control fails to work:

1.5 Check that the batteries are new and correctly fitted.

Replace if necessary.

2. How to wire a plug

To change the plug supplied with this appliance, follow the

instructions below. The instructions assume that the wire

has been cut.

WARNING – FAILURE TO CONNECT THE WIRES

CORRECTLY COULD PUT PEOPLE AT RISK FROM

ELECTRIC SHOCK OR FIRE. IF IN DOUBT CONSULT

A QUALIFIED ELECTRICIAN.

UK Plug

Suitable for use in Cyprus, Malta, Ireland & Great Britain.

Earth wire

Neutral wire

Outer Insulation

Fuse

Cable grip

UK Plug Supplied

Type BS1363

Live wire

Live Wire Brown Terminal L / RED

Neutral Wire Blue Terminal N / BLACK

Earth Wire Green & Yellow

Stripes Terminal E / / GREEN or

GREEN & YELLOW

THIS APPLIANCE MUST BE EARTHED

European Plug

Suitable for use in Austria, Belgium, Bulgaria, Czech

Republic, Denmark, Estonia, Finland, France, Greece,

Hungary, Germany, Italy, Latvia, Lithuania, Luxembourg,

Netherlands, Poland, Portugal, Romania, Slovakia,

Slovenia, Spain & Sweden.

Cable grip

Outer Insulation

Neutral wire

Earth wire

Live wire

Typical European Plug

Type CEE 7/7

2.1 Dispose of the old plug safely. Ensure the new plug has the

relevant approval marking and is not cracked or chipped.

2.2 Expose 4cm of the coloured wires and trim to the correct

lengths so that they comfortably reach the correct terminals.

2.3 Ensure that the Earth wire has more slack than any of the

other wires.

2.4 Remove some of the insulation to leave about 6mm (screw

terminals) to 12mm (winding around screw) of exposed

metal core on each wire, taking care not to damage or

remove the metal strands.

2.5 Twist the strands of the wire together.

2.6 Loosen the screw heads above each terminal.

2.7 Push the metal wire into the hole beneath each screw head

or, dependent on plug design, wind the metal wire around

the screw.

2.8 Ensure that the insulation reaches right up to each terminal

as illustrated and there are no loose strands of wire.

2.9 Ensure the cable sits correctly under the cable grip and

tighten to secure, taking care that the connecting wires

inside the plug are not strained.

2.10 Refer to Technical Specification for fuse rating and fit the

appropriate fuse into the plug (UK Only).

2.11 Attach the plug cover.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yeoman CL Electric Range Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info