Bedienungsanleitung Yokis Thermarp 5454489 (Seite 25 von 40) (Englisch)

785688

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

P25DS1054-057A

8. REMOTE SWITCH-OFF

The device has two inputs (AUX) for connecting a potential-free contact to which a telephone dialler can be

connected, for example, to remotely switch the thermostat on and off using a telephone.

The contact can be in one of the following positions:

- open: normal operation (according to the programming set via keypad).

- closed: thermostat in off operation.

The remote off condition is indicated on the display by the ﬂashing of the symbol to differentiate it from the

keypad off condition.

Note: This function must be operated via the Advanced Conﬁguration (ADV) menu. The auxiliary input parameter

must be set to “diG”.

IMPORTANT: Remote off condition (contact closed) takes priority over any other programming and therefore

the thermostat will remain in the off condition until the contact returns to the open position.

9. THERMOSTAT RESET

This can be used to delete any settings made and reload the default settings.

Proceed as follows:

Disconnect the thermostat from the wall base and reconnect it.

While the buttons are ﬂashing, keep the button pressed until “dEF” appears on the display.

Resetting to default settings will clears all settings in the conﬁguration parameters:

Time and date

Edit programs

Change temperature (T1), T2, T3

Timer setting

Advanced menu conﬁgurations

IMPORTANT: Resetting to default parameters will not delete the wireless conﬁgurations made on the thermostat.

To delete the wireless conﬁgurations, see chapter “7.6.6. Def 25 : Thermostat wireless conﬁguration reset”.

10. INSTALLATION

10.1. SAFETY WARNINGS

The following instructions must be observed when installing the product:

The product must be installed by a qualiﬁed professional, scrupulously respecting the wiring diagram.

Do not power or connect the product if any of its parts are damaged. Do not carry out repairs and contact

technical support directly.

Do not use the product for purposes other than those speciﬁed.

The device must be installed and put into operation in accordance with current legislation on electrical

systems.

The product can be used in a category 3 and grade 2 pollution measurement environment.

Where it is necessary to guarantee galvanic insulation towards the boiler, it is essential to install the REL1C

accessory (see diagram SD541-6054 in the MTR2000 product card).

10.2. HOW TO START THE THERMOSTAT

The Thermarp accessory is ideal for wall mounting. Alternatively, it can be installed on a ﬂush mounting box

Mod. 503.

The thermostat must be installed at a height of about 1.5 m above the ﬂoor, protected from direct radiation,

away from doors, windows, heat sources, positions with excess or total lack of ventilation.

The YOKIS THERMARP thermostat runs on batteries (2 x 1.5 V AAA / LR03 type batteries).

Fix the base to the wall using the screws provided.

Open the rear compartment of the thermostat timer to insert the batteries, checking the polarity indicated

on the battery compartment.

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yokis Thermarp 5454489 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yokis Thermarp 5454489

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info