Bedienungsanleitung Yokis Thermarp 5454489 (Seite 35 von 40) (Englisch)

785688

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

P35DS1054-057A

With wireless connection (via Yokis MTR module) to the solenoid valves and to the boiler. The installer is

responsible for managing the OR function of the boiler again in this case and this is usually achieved by

means of solenoid valves which have a dedicated electrical output which is energised when the solenoid

valve is open.

With wireless connection (via Yokis MTR module) to the solenoid valves and boiler. In this case, no speciﬁc

wiring is needed to implement the OR function. However, the presence of a Yokis Hub is indispensable in

the system.

Case A)

Simply follow the instructions in the two previous paragraphs for each thermostat according to whether or not

you use the Yokis PRO app for conﬁguration:

Single-zone thermostat conﬁguration with direct wiring

YOKIS PRO: Single-zone thermostat conﬁguration with direct wiring

However, in this case it is necessary to prepare the wiring from each thermostat to its own zone solenoid valve

and also to manage the OR function towards the boiler using the usual wiring techniques (mainly using solenoid

valves with dedicated output).

Note: When conﬁgured in this way, the thermostat cannot be accessed remotely or locally via the Yno app. To

be so, a Yokis Hub must also be also installed in the system.

Case B)

Simply follow the instructions in the two previous paragraphs for each thermostat according to whether or not

you use the Yokis PRO app for conﬁguration:

Single-zone thermostat conﬁguration with wireless connection (via MTR) and check

YOKIS PRO: Single-zone thermostat conﬁguration with wireless connection (via MTR)

However, in this case it is necessary to prepare the wiring from each thermostat to its own zone solenoid valve

and also to manage the OR function towards the boiler using the usual wiring techniques (mainly using solenoid

valves with dedicated output).

Note: When conﬁgured in this way, the thermostat cannot be accessed remotely or locally via the Yno app. To

be so, a Yokis Hub must also be also installed in the system.

Case C)

Four steps are required in this case:

Add the MTR modules which will control the zone solenoid valves.

Add an additional MTR to control the boiler (in OR mode).

Add and conﬁgure the thermostats, one for each zone. Thermostats are all considered as the Control

Points by the app.

Connect each thermostat to its own MTR actuator module (for the solenoid valve in your area) AND to

the boiler MTR module.

The MTR modules must be added to the Yokis PRO app in the usual way (automatic or manual detection).

However, it is necessary to specialise their function. Therefore, all MTRs which will be connected to the zone

solenoid valves must use the motorised valve symbol:

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yokis Thermarp 5454489 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yokis Thermarp 5454489

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info