540485
16
Zoom out
Zoom in
Vorherige Seite
1/174
Nächste Seite
<3. INSTALLATION>
3-6
IM 01F06A00-01EN
3.4 Cryogenic and High Process
Temperature Version
Insulation
When you are using Cryogenic and High Process
Temperature version of digitalYEWFLO Vortex
Flowmeter (Option code: /HT, /LT), refer to following
contents.
Installing Cryogenic Version
For cryogenic applications, use stainless steel
mounting bolts and nuts to install the owmeter.
These can be ordered separately from
YOKOGAWA. Cover the owmeter body with
heat insulating material so that the owmeter
can be maintained at ultra-low temperatures.
Maintenance for Cryogenic Applications
DY/LT uses special materials that produce
vortex owmeter for cryogenic applications.
When you are replacing a shedder bar, specify
Cryogenic Version shedder bar. To avoid
condensing in the terminal box, ensure that the
wire connecting port is well sealed.
F0308.ai
Bracket
Cold insulating material
Installing High Process Temperature
Version
Installation of the owmeter is the same as the
standard type. Cover the owmeter body with
heat insulating material following instruction of
“CAUTION”.
CAUTION
Keep the upper limit of heat insulating material to
prevent overheating of the terminal box.
Seal the Heat-Insulator to avoid hot-air leakage.
UPPER LIMIT OF
Heat-Insulator
UPPER LIMIT OF
Heat-Insulator
50mm min. 50mm min.
Nominal Size: 100mm or under
Nominal Size: 150mm or over
F0309.ai
Maintenance for High Process
Temperature Applications
DY/HT uses special materials that produce
vortex owmeter for High Process Temperature
applications When you are replacing a
shedder bar or a gasket, specify High Process
Temperature Version.
3.5 Mounting Procedures
WARNING
The Vortex Flowmeter is a heavy instrument.
Please be careful to prevent persons from
injuring whin it is handled.
Before installing the instrument verify the following.
The direction of ow should match to the arrow
mark on the instrument body. When changing the
orientation of the terminal box, refer to Chapter 11
“MAINTENANCE.”
1. Installation of Vortex owmeter of the wafer and
ange type is shown in Table 3.3.
When installing the wafer type vortex owmeter,
it is important to align the instrument bore with
the inner diameter of the adjacent piping.
To establish alignment, use the four collars
supplied with the instrument.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yokogawa DY Vortex Flowmeter wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info