Bedienungsanleitung Yukon Photon XT (Seite 6 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

663733

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

VIDEO OUTPUT

The riflescope is equipped with a video output (7) designed to connect external recording devices and to transmit

video signal to monitors, TV sets etc.

џ Use the supplied cable to connect an external signal receiver to the video output (7).

џ Turn on the scope – image will appear on the external device. Please make sure the external device is in the AV

mode.

To record video, you can use video recorders such as Yukon MPR (#27041) / CVR640 (#17044) and others.

NOTE: it is not recommended to attach the CVR640 on the riflescope because the video recorder is not designed for

heavy shock resistance.

ACCESSORIES

The riflescope is fitted out with an additional Weaver rail (8) which allows you to attach accessories like:

џ IR Illuminators Pulsar-805/Pulsar-940/Pulsar- X850 (#79071/79076/79074)

џ Laser IR Illuminators Pulsar L-808S/Pulsar L-915 (#79072/79075)

MAINTENANCE AND STORAGE

џ The riflescope features IPX4 degree of protection (protected against splash water) but cannot be submerged in

water.

џ Attempts to disassemble or repair the scope will void the warranty!

џ Clean the scope's optical surfaces only if necessary, and use caution. First, remove (by blowing with a blower

brush or canned air) any dust or sand particles. Then proceed to clean by using camera/lens cleaning equipment

approved for use with multicoated lenses. Do not pour the solution directly onto the lens!

џ The riflescope can be used in operating temperatures ranging from -15 °C...+50 °C. However, if it has been

brought indoors from cold temperatures, do not turn it on for 2 to 3 hours. This will prevent external optical surfaces

from fogging.

џ Always store the unit in its carrying case in a dry, well-ventilated space. For prolonged storage, remove the

batteries.

TROUBLESHOOTING

Listed below are some potential problems that may occur when using the scope. Carry out the recommended checks

and troubleshooting steps in the order listed. Please note that the table does not list all of the possible problems. If the

problem experienced with the scope is not listed, or if the suggested action meant to correct it does not resolve the

problem, please contact the manufacturer.

Next to the icon horizontal arrows appear, in the top right corner - location of the reticle along the X coordinate (see

pic.3).

Rotate the controller to move the reticle until it matches the point of impact.

First press of the controller enables vertical movement of the reticle (axis X appears on the

data panel), second press enables horizontal movement (icon Y). Initial position of the

reticle is in the centre of the display (coordinates X=0; Y=0). The field of view shows

positive and negative numbers which indicate movement relative to the coordinates “X=0;

Y=0”. Travel range of the reticle is +/-30 clicks horizontally and vertically.

Hold down the controller to save zeroing settings and to exit zeroing mode.

Take another shot - the point of impact should now coincide with the aiming point.

The scope should now be zeroed-in for the specified distance.

Note: each click equals to a 25mm/17 mm move of the reticle in the horizontal and vertical

plane at 100 m.

Pic.3

◄

►

X=+10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yukon Photon XT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info