The CGO SteadyGrip™ is a ground handle designed to extend the CGO3 3-axis gyro
stabilized camera from the sky to the ground. The camera pitch controller allows
precise camera angle control on the go using your mobile device as a display. The
SteadyGrip's ergonomic design is capable of holding up to a 6.4 inch mobile device.
CGO3 (available separately) is an innovave combinaon of 3-axis brushless
gimbal, camera and digital video downlink.
The Self-Stabilizing gimbal makes it possible to capture amazing photographs and
video footage for an array of uses. And the built-in digital video link delivers
streaming video to 5.8GHz WiFi compable iOS® and Android™ equipped devices
including smart-phones and tablets as well as YUNEEC Personal Ground Staons.
GENERAL SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to use this product in the intended manner as described in
instrucon manual can result in damage to the product, property and/or cause
serious injury. This product is not a toy! If misused it can cause serious bodily harm
and damage to property.
WARNING: As the user of this product you are solely and wholly responsible for
operang it in a manner that does not endanger yourself and others or result in
damage to the product or the property of others.
Always allow CGO3 and SteadyGrip™ to inialize properly by seng the Steady-
Grip™ on a flat and stable surface prior to switching it on and allowing the Steady-
Grip™ and CGO3 to inialize properly which somemes takes about 4-8 seconds.
Always operate your SteadyGrip™ in a respecul and safe manner.
Do not aempt to operate your equipment in areas with potenal magnec and/or
radio interference including areas nearby broadcast towers, power transmission
staons, high voltage power lines, etc.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15
of the FCC rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instrucons, may cause harmful interference to radio
communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operaon is subject to the
following two condions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operaon.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in a
residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
ons, may cause harmful interference to radio communicaons. However, there
is no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon,
which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE WARNING
• This equipment must be installed and operated in accordance with provided
instrucons and the antenna(s) used for this transmier must be installed to
provide a separaon distance of at least 20 cm from all persons and must not be
co-located or operang in conjuncon with any other antenna or transmier.
End-users and installers must be provide with antenna installaon instrucons
and transmier operang condions for sasfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interfer-
ence that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitaon est autorisée aux deux
condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est suscepble d'en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for
an uncontrolled environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies
pour un environnement non contrôlé
BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Lithium Polymer (LiPo) baeries are significantly more volale than
alkaline, NiCd or NiMH baeries. All instrucons and warnings must be followed
exactly to prevent property damage and/or serious injury as the mishandling of
LiPo baeries can result in fire. By handling, charging or using the included LiPo
baery you assume all risks associated with LiPo baeries. If you do not agree with
these condions please return the complete product in new, unused condion to
the place of purchase immediately. You must always charge the LiPo baery in a
safe, well-venlated area away from flammable materials.
Never charge the LiPo baery unaended at any me. When charging the baery
you must always remain in constant observaon to monitor the charging process
and react immediately to any potenal problems that may occur.
Aer flying/discharging the LiPo baery you must allow it to cool to
ambient/room temperature before recharging.
To charge the LiPo baery you must use only the included charger or a suitably
INSTALLING THE LiPo BATTERY
CHARGING THE BATTERY
ATTACHING THE CGO3 TO THE STEADYGRIP™
WARNING: Before switching on the SteadyGrip™ , it is highly recommended to
first securely aach the CGO3 to your SteadyGrip™.
QUICK TIP: Make sure you have your microSD card with enough space for photos
and videos handy.
STEP 1) Remove the protecve cover for the contactor as illustrated.
STEP 2) Carefully slide the top part of the CGO3 (that also aaches below the nose
of the TYPHOON) onto the mount below the front part of the SteadyGrip™. A
corresponding ‘click’ will be noced once the CGO3 has securely been installed
into the slide-in mount on the SteadyGrip™.
STEP 3) Insert a microSD card into the corresponding slot on the boom of the
CGO3. You can use the included 16GB card (from your RTF package) or any Class
10 microSD card up to 128GB.
SPECIFICATIONS
STEADYGRIP™
Dimensions: 230 X 70 X 190 mm (9.06 X 2.76 X 7.48 in)
Weight (without gimbal/baeries): 350 g (12.35 oz)
Angle Control Range (Pitch): 30° - 85°
Required Baeries: 11.1 V 1400 mAh 3C
Runme: 90 min (depending on usage)
CGO3
Dimension: 4.2 x 5.0 x 3.1 in (106x128x80 mm)
Weight: 7.05oz (200g)
Sensor: 1/2.3” CMOS
Effecve Pixels: 12 Megapixels
Camera lens: 0.6in (14 mm)/F2.81.4 in/35 mm
FOV: 115 Degree
Electronic Shuer: 1/30 —— 1/8000
Power Consumpon: 18 W
Video Transmission Range: Up to 500 m (1640 )
Transmission System: 5.2 Ghz — 5.8 Ghz
Video UHD: 4K 30FPS
CGO3 APP COMPATIBLE DEVICES
Android:
Mobile Devices with 5.8GHz Support
WINDOWS SYSTEM
REQUIREMENTS
Windows XP (Service Pack 2 or later)
or Vista
3.2GHz Penum 4 or faster
Minimum 4GB of system RAM
MAC SYSTEM
REQUIREMENTS
Mac OS® X 10.4.11 or later
2.0GHz Intel Core Duo or faster
Minimum 4GB of system RAM
NOTICES AND WARNINGS
IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes
and other collateral informaon is subject to change at the sole discreon of
Yuneec. For the most up-to-date informaon please visit the corresponding
product page at www.Yuneec.com or contact the nearest Yuneec office or
authorized distributor.
The following special language terms are used throughout the product literature to
indicate various levels of potenal harm when operang this product:
NOTICE: Procedures, which if not properly followed, create a possibility of property
damage and/or lile to no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of
property damage and/or a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage and/or serious injury or create a high probability
of superficial injury.
WARNING: Read the ENTIRE instrucon manual to become familiar with the
features of the product before operang. Failure to operate the product correctly
can result in damage to the product, property and/or cause serious injury.
WARNING:This is a sophiscated consumer product. It must be operated with
cauon and common sense, and requires some basic mechanical ability. Failure to
operate this product in a safe and responsible manner could result in damage to the
product, property and/or cause serious injury. This product is not intended for use
by children without direct adult supervision. Do not use with incompable
components or alter this product in any way outside of the instrucons provided by
Yuneec. The instrucon manual contain instrucons for safety, operaon and
maintenance. It is essenal to read and follow all the instrucons and warnings
prior to assembly, setup and/or use in order to operate the product correctly and
avoid damage or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT
A TOY.
Apple iOS:
iphone 5/5c/5s/6/6 Plus
ipad mini/mini+/3/4
OVERVIEW
SteadyGrip™ Acon Ground Handle for CGO Series Camera.
1. CGO3
2. Main Status LED
3. Pitch Control Roller Wheel
4. Mode Switch Boon
5. Rubberized Ergonomic Grip
6. Charging Port
Install the LiPo Baery in the baery compartment with the side aached a label
facing to the baery compartment. Once you've heard and felt a noceable "click",
it indicates the baery has been installed securely.
The other way is:
Step 1) Switch the OPEN with slight force and the LiPo baery will be ejected, then it
can be taken from the baery compartment.
Step 2) Insert the Baery with the side aached a label facing downward.
Step 3) Power the Charger from a 100-240V AC outlet using the 12.6V 1A
adapter/power supply, the red solid LED on the adaptor indicates the baery is being
charged. It will take approximately 2 hours to charge a fully discharged (not
over-discharged) baery. The LED will glow solid green when fully charged.
ON
There are two ways to charge the baery.
Power the SteadyGrip™ from a 100-240V AC outlet using the 12.6V 1A
adapter/power supply as illustrated. The red solid LED on the adaptor indicates the
baery is being charged. It will take approximately 2 hours to charge a fully
discharged (not over-discharged) baery. The LED will glow solid green when fully
charged..
SteadyGrip™ LED STATUS:
Main Status LED:
Upon Powering on: Green LED blinking for twice and
then solid GREEN
Low Voltage Warning: RED LED blinking
Power Cut-off: LED solid red
Mode LED:
Pitch Follow Funcon on GREEN LED solid
Pitch Follow Funcon offGREEN LED off
STEP 4)Powering on and inializaon. Place your
SteadyGrip™ on a flat and stable surface, then switch on
the SteadyGrip™ and it will inialize aer 4-8 seconds of
no movement or vibraon.
CUSTOMER SERVICE
YUNEEC EU
24568 Kaltenkirchen, Germany
+49 4191 932620
eusales@yuneec.com
YUNEEC AU
53 Ellemsea Circuit, Lonsdale
South Australia 5160
+61 (0) 8 8186 3301
aussales@yuneec.com
YUNEEC USA
5555 Ontario Mills Parkway,
Ontario, CA91764, USA
1 855 2848888
sales@yuneec.com
YUNEEC HK
2/F, Man Shung Industrial Building,
7 LaiYip Street, Kwun Tong,
Kowloon, Hong Kong
852 3616 6071
asiasales@yuneec.com
hp://yuneec.com/support
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
TAKING PHOTOS AND RECORDING VIDEOS
1) To take a sll photo press the red Photo Taking/Video Recording buon on your
APP You’ll hear an audible shuer sound from the APP and the LED indicator on
CGO3 front will flash in blue and green. It will take approximately 5 seconds to
capture the photo and before you can take another sll photo.
IMPORTANT NOTE: You cannot take sll photos while recording video. You MUST
stop recording video in order to take sll photos.
2) To start/stop recording videos, slide the Mode buon to Video Recording, then
press the red buon to start. You’ll hear an audible indicaon from the APP each
me the recording starts/stops. During recording, the LED indicator on CGO3
front will flash in blue and green. There will be recording me length display on the
APP Screen.
3) To start/stop recording video, simply press the red buon located on the APP.
You’ll hear an audible indicaon from the APP each me the recording
starts/stops. And while video is recording, the LED indicator on the front of GCO3
will flash blue and green, and there will be an indicator showing me length of the
recording on the APP screen.
IMPORTANT NOTE: You can choose to record video at 48, 50 (PAL) or 60 (NTSC)
frames per second by tapping the corresponding buon near the upper le-hand
corner on main screen of the APP. Keep in mind that the delay in the live video
stream will be lowest at 48 and 50 as compared to 60 frames per second.
compable LiPo baery charger. Failure to do so may result in a fire causing
property damage and/or serious injury.
If at any me the LiPo baery begins to balloon or swell, disconnue charging or
discharging immediately. Quickly and safely disconnect the baery, then place it in
a safe, open area away from flammable materials to observe it for at least 15
minutes.
Connuing to charge or discharge a baery that has begun to balloon or swell can
result in a fire. A baery that has ballooned or swollen even a small amount must be
removed from service completely.
Do not over-discharge the LiPo baery. Discharging the baery too low can cause
damage to the baery resulng in reduced power, flight duraon or failure of the
baery enrely. LiPo cells should not be discharged to below 3.0V each under load.
Store the LiPo baery at room temperature and in a dry area for best results.
When charging, transporng or temporarily storing the LiPo baery the tempera-
ture range should be from approximately 40–120°F (5–49°C). Do not store the
baery or aircra in a hot garage, car or direct sunlight. If stored in a hot garage or
car the baery can be damaged or even catch fire.
WARNING: All instrucons and precauons must be read and followed exactly and
you must follow instrucons of the baery manufacturer.
WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage and serious injury or create a high probability
of superficial injury.
Failure to exercise care while using this product and comply with the following
condions and guidance could result in product malfuncon, excessive heat, fire,
property damage, and ulmately injury.
Lithium lon baeries are not toys. For the purpose of the document Li-lon, Li-Po,
Li-Fe, NiCd or NiMH baeries will be described as "Baeries".
Handling and Storage:
Lithium Polymer (LiPo) baeries are significantly more volale than alkaline, NiCd
or NiMH baeries. All instrucons and warnings must be followed exactly to
prevent property damage and/or serious injury as the mishandling of LiPo baeries
can result in fire. By handling, charging or using the included LiPo baery you
assume all risks associated with LiPo baeries. If you do not agree with these
condions please return the complete product in new, unused condion to the
place of purchase immediately.
ATTACHING A MOBILE DEVICE TO THE STEADYGRIP™
Step 1) Press the curved lip at the
top front of the SteadyGrip™ as
illustrated and fit your Mobile
Device with the screen facing
toward the Main LED and Pitch
Control Wheel.
Step 2) Connect your Mobile
Device to the CGO3’s WiFi by
selecng CGO3’s SSID and by
entering the WiFi Key / Password:
1234567890.
Download the free APP named as
CGO3 to smart device at the APP
Store or Google Play Store.Install
the APP to your 5.8GHz WiFi
capable device.
NOTICE: Please be sure to enter
the CGO3 WiFi first before
entering the APP.
CGO3 APP
WB
ISO 32
1/250s
17:24:12
N/A
The SteadyGrip™ features a camera pitch controller that allows precise camera
angle control on the go. Simply roll the pitch control wheel forward to move the
camera pitch/angle downward and
roll the pitch control wheel
backward to move the camera
pitch/angle upward. Please review
these instrucons along with the
illustraons to familiarize yourself
on how to control the CGO3 with
your SteadyGrip™.
USING THE CAMERA PITCH CONTROL WHEEL
Any informaon above might be changed due to the soware update. For the
latest documents, please check the official website.
CGO3 APP COMPATIBLE DEVICES
Apple iOS:
iphone 5/5c/5s/6/6Plus ipad
mini/mini+/3/4
Android:
Mobile Devices with 5.8GHz Suport
NOTE: When SteadyGrip™ is in Pitch Follow status, the gimbal camera
tracks SteadyGrip™ in pitch direcon, and the gimbal pitch control
roller wheel on SteadyGrip™ is disabled.
ON
8
9
7. On/Off Switch
8. 11.1V 1400mAh 3C LiPo Baery
9. Mode LED
10. Charger
11. Adapter
12. Baery LED Status Indicator
10
11
12
ON
OPEN
SWITCHING THE MODE
There are two modes of SteadyGrip: Pitch Follow Mode and Angle
Mode.
Pitch Follow Mode allows the gimbal to track SteadyGrip™in pitch
direcon. The Pitch Follow Mode LED status indicator will be solid
green.
In Angle Mode, the gimbal scks to a fixed direcon instead of follow-
ing the movement of the SteadyGrip. The user can control the Pitch
Direcon through pitch control roller wheel.
NOTICE: The default mode of SteadyGrip™is Pitch Follow Mode.
To Enter Angle Mode:
Press the Mode Switch Buon on the top of the SteadyGrip™to exit
the Pitch Follow mode. The Pitch Follow Mode LED status indicator will
be off. The SteadyGrip™will enter Angle Mode.
To Enter Pitch Follow Mode:
Press Mode Switch Buon again to enter Pitch Follow Mode. The Pitch
Follow Mode LED status indicator will be solid green.
ON
OFF
NOTICE: The AC plug type will vary depending on the region in which the product
was imported/purchased (AU = Australian; EU = European; UK = United Kingdom;
US = United States).
NOTICE: The CGO3 can be supplied with power through SteadyGrip™ by the
Lipo Balance Connetor Charge Lead (sold seperately) when the contact is
damaged.
Brauchen Sie Hilfe? Stellen Sie Ihre Frage.
Missbrauch melden von Frage und/oder Antwort
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yuneec ActionCam wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
