Bedienungsanleitung Yuneec Tornado H920 Plus (Seite 10 von 40) (Englisch)

669702

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CHARGING THE LIPO FLIGHT BATTERY

Connecting to the power source : the A10 Dual Balance Charger comes with built in

switching power supply. You can connect the AC power cord directly to the main AC

socket (110 to 240V AC).

NOTICE: While the A10 is connected to a

suitable 110 to 240V AC power source, the

combined power output for Channel A and

Channel B is 200W, capable of charging two

6-Cell (6S), 4,000mAh LiPo battery packs at

4.3A.

CONNECTING THE B

ATTERY

CHARGING

BATT/PROGRAM Select: Press INC and DEC to go through all the programs and press

START/ENTER to enter LiPo BATT Program (for flight BATT) or Li-ion BATT Program(for

proaction™).

Mode Select: Press INC and DEC to go through all the modes and press START/ENTER

to enter LiPo Balance Charge Mode (for aircraft’s flight battery), to enter Li-ion

Balance Charge Mode (for ProAction ground handle).

Battery Setting: Press START/ENTER, the current value will start to blink, press INC

and DEC to change the value and press START/ENTER to confirm your setting. For the

H920 Plus battery, it is recommended to set 4A (no more than 8A). For ProAction™

battery, it is recommended to set 2A (no more than 3A).

At the same time, the battery cells number will start blinking, press INC and DEC to

change the value and press START/ENTER to confirm your setting.

For the H920 Plus battery, 6S should be selected. For ProAction™, 4S should be

selected.

Program Start: Press and hold START/ENTER for 3 seconds to start the program.

The charger is detecting the battery cell.

NOTICE:

R shows the number of cells detected by the charger and S is the number of

cells set by you at the previous screen. If both numbers are not identical, press STOP

to go back to previous screen to recheck the number of cells of the battery pack

before going ahead. If both numbers are identical, press START/ENTER to start

charging process.

If the number of cells do not match after double checking the connection, please

contact technical support.

BUTTON DESCRIPTIONS

CH A / CH B: Used to switch from Channel A

to B or Channel B to A.

BATT PROG / STOP: Used to stop the

progress or go back to previous step/screen

DEC: Used to go through the menus and

decrease the parameter value.

INC: Used to go through the menus and

increase the parameter value.

ENTER / START: Used to enter parameter or

store parameter on screen.

CHARGING THE LIPO FLIGHT BATTERY

Connecting to the power source : the A10 Dual Balance Charger comes with built in switching power

supply. You can connect the AC power cord directly to the main AC socket (110 to 240V AC).

NOTICE: While the A10 is connected to a suitable

110 to 240V AC power source, the combined po-

wer output for Channel A and Channel B is 200W,

capable of charging two 6-Cell (6S), 4,000mAh

LiPo battery packs at 4.3A

CONNECTING THE BATTERY

CHARGING

BATT/PROGRAM Select: Press INC and DEC to go through all the programs and press START/ENTER

to enter LiPo BATT Program (for ight BATT) or Li-ion BATT Program(for proaction™).

Mode Select: Press INC and DEC to go through all the modes and press START/ENTER to enter LiPo

Balance Charge Mode (for aircraft’s ight battery), to enter Li-ion Balance Charge Mode (for ProActi-

on ground handle).

Battery Setting: Press START/ENTER, the current value will start to blink, press INC and DEC to

change the value and press START/ENTER to conrm your setting. For the H920 Plus battery, it is

recommended to set 4A (no more than 8A). For ProAction™ battery, it is recommended to set 2A (no

more than 3A).

At the same time, the battery cells number will start blinking, press INC and DEC to change the value

and press START/ENTER to conrm your setting.

For the H920 Plus battery, 6S should be selected. For ProAction™, 4S should be selected.

Program Start: Press and hold START/ENTER for 3 seconds to start the program.

The charger is detecting the battery cell.

NOTICE: R shows the number of cells detected by the charger and S is the number of cells set by you

at the previous screen. If both numbers are not identical, press STOP to go back to previous screen

to recheck the number of cells of the battery pack before going ahead. If both numbers are identical,

press START/ENTER to start charging process.

If the number of cells do not match after double checking the connection, please contact technical

support.

BUTTON DESCRIPTIONS

CH A / CH B: Used to switch from Channel A to B or

Channel B to A.

BATT PROG / STOP: Used to stop the progress or go

back to previous step/screen

DEC: Used to go through the menus and decrease the

parameter value.

INC: Used to go through the menus and increase the

parameter value.

ENTER / START: Used to enter parameter or store

parameter on screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yuneec Tornado H920 Plus Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yuneec Tornado H920 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info