Bedienungsanleitung Yuneec Tornado H920 (Seite 14 von 39) (Englisch)

633010

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

CHARGING THE LIPO FLIGHT BATTERY

Connecting to the power source : the A10 Dual Balance Charger comes with built in

switching power supply. You can connect the AC power cord directly to the main AC

socket (110 to 240V AC).

NOTICE: While the A10 is connected to a

suitable 110 to 240V AC power source, the

combined power output for Channel A and

Channel B is 200W, capable of charging two

6-Cell (6S), 4,000mAh LiPo battery packs at

4.3A.

CONNECTING THE BATTERY

CHARGING

BATT/PROGRAM Select: Press INC and DEC to go through all the programs and press

START/ENTER to enter LiPo BATT Program (for flight BATT) or Li-ion BATT Program(for

proaction™).

Mode Select: Press INC and DEC to go through all the modes and press START/ENTER

to enter LiPo Balance Charge Mode (for aircraft’s flight battery), to enter Li-ion

Balance Charge Mode (for ProAction ground handle).

Battery Setting: Press START/ENTER, the current value will start to blink, press INC

and DEC to change the value and press START/ENTER to confirm your setting. For the

TORNADO H920 battery, it is recommended to set 4A (no more than 8A). For

ProAction™ battery, it is recommended to set 2A (no more than 3A).

At the same time, the battery cells number will start blinking, press INC and DEC to

change the value and press START/ENTER to confirm your setting.

For the TORNADO H920 battery, 6S should be selected. For ProAction™, 4S should

be selected.

Program Start: Press and hold START/ENTER for 3 seconds to start the program.

The charger is detecting the battery cell.

NOTICE: R shows the number of cells detected by the charger and S is the number of

cells set by you at the previous screen. If both numbers are not identical, press STOP

to go back to previous screen to recheck the number of cells of the battery pack

before going ahead. If both numbers are identical, press START/ENTER to start

charging process.

If the number of cells do not match after double checking the connection, please

contact technical support.

ASSEMBLING THE H920

INSTALLING THE MOTOR ARMS

Fold the motor arms upwards and secure them using the straight knurled nut cover

located on the motor arms.

NOTICE: Don’t over tighten the straight knurled nuts, It may cause deformation of the arms.

INSTALLING THE PROPELLERS

Always ensure propellers are installed properly and with thread locker on the

fasteners. The rotors of the YUNEEC TORNADO H920 are made of high-strength

carbon fiber, the motors are extremely powerful, meaning that if the device is misused

there is a risk of material damage, serious injury and even fatal injury.

Mount the propellers on the motors and note the pointers ‘A’ and ‘B’ given on the

motor arms. This distinction between ‘A’ and ‘B’ refers to the rotation direction of the

motors. The rotation direction of the motors must match the rotation direction of the

propellers. Mount propeller ‘A’ on motor ‘A’ and propeller ‘B’ on motor ‘B’ and use the

screws with spring plate and 2mm Hexdriver enclosed to carefully screw in the propellers.

IMPORTANT NOTE: If the propellers are installed in the wrong places, it may cause crash.

INSTALLING THE FLIGHT BATTERIES

After the flight batteries has been fully charged, they are ready to be installed in the

TORNADO H920:

STEP 1) Open the battery compartment flap with the status LED mounted on it by

carefully pulling the top edge of the flap.

STEP 2) Slide the batteries into the compartment with the EC3 blue, polarity-

protected connector leads / wires downward.

WARNING: The aircraft can take-off with 2 or 3 batteries. If utilizing 2 flight batteries,

make sure the 2 batteries are placed evenly within the two sides to balance the

aircraft. The voltage between each battery pack must be within 0.1V prior to

connecting the batteries to the aircraft. Be sure to use the included battery voltage meter.

STEP 3) Connect the flight battery to the relevant socket above the respective battery

on the H920 using the EC3 blue, polarity-protected connector.

NOTICE: The white socket is for battery charging, do not connect it to any port when

installing the batteries. If you do not install the battery in the correct orientation it will

not be possible to make a positive connection.

STEP 4) Fasten the battery belt, Close the battery door and ensure the door is closed

safely by the magnet.

INSTALLING THE MOTOR ARMS INSTALLING THE PROPELLERS INSTALLING THE FLIGHT BATTERIES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yuneec Tornado H920 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yuneec Tornado H920

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info