633005
1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
NOTICES AND WARNINGS
OVERVIEW
1 CGO3 Gimbal Camera
2 Camera Microphone
3 Camera LED Status Indicator
4 Camera Lens
5 5.8GHz Antenna
6 Main LED Status Indicator
7 Power Switch
8 Proportional Control Rate Slider
9 USB Connector/Charging Port
10 Audio/Earphone Jack
11 Take Still Photo Button
12 Start/Stop Motors Button
13 Rudder/Yaw Control (for Mode 2 and Mode 1)
14 Throttle/Altitude Control (for Mode 2)
Elevator/Pitch Control (for Mode 1)
15 5.8GHz Antenna (located inside the case)
16 Status Indicators (for ST10+ battery, 5.8GHz
WiFi and GPS)
17 2.4GHz Antenna (located inside the handle)
18 Start/Stop Video Recording Button
19 Flight Mode Selection Switch
20 Aileron/Roll Control (Mode 2 and Mode 1)
21 Elevator/Pitch Control (Mode 2)
Throttle/Altitude Control (Mode 1)
22 Power Switch
23 Volume and Navigation Touch-Activated
Buttons Volume Down/VolumeUp/Menu/Home/Back)
24 CGO3 Pitch Angle/Position Control
Slider
25 SD Card Slot (located under the battery)
6
7
8
9
10
11
12
13
14
15 16 17
18
19
20
21
22
23
24
25
TYPHOON Q500 4K Quickstart V3.0
IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes and other collateral informaon is subject to
change at the sole discreon of Yuneec. For the most up-to-date informaon please visit the corresponding product page at
www.Yuneec.com or contact the nearest Yuneec office or authorized distributor.
The following special language terms are used throughout the product literature to indicate various levels of potenal harm
when operang this product:
NOTICE: Procedures, which if not properly followed, create a possibility of property damage and/or lile to no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of property damage and/or a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and/or
serious injury or create a high probability of superficial injury.
WARNING: Read the ENTIRE quick start guide and instrucon manual to become familiar with the features of the product
before operang. Failure to operate the product correctly can result in damage to the product, property and/or cause serious injury.
WARNING: This is a sophiscated consumer product. It must be operated with cauon and common sense, and requires some
basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in damage to the product,
property and/or cause serious injury. This product is not intended for use by children without direct adult supervision. Do not
use with incompable components or alter this product in any way outside of the instrucons provided by Yuneec. The quick
start guide and instrucon manual contain instrucons for safety, operaon and maintenance. It is essenal to read and follow
all the instrucons and warnings prior to assembly, setup and/or use in order to operate the product correctly and avoid damage
or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.
GENERAL SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to use this product in the intended manner as described in the quick start guide and instrucon manual can
result in damage to the product, property and/or cause serious injury. A Radio Controlled (RC) mulrotor aircra, APV plaorm,
drone, etc. is not a toy! If misused it can cause serious bodily harm and damage to property.
WARNING: As the user of this product you are solely and wholly responsible for operang it in a manner that does not endanger
yourself and others or result in damage to the product or the property of others.
Keep your hands, face and other parts of your body away from the spinning propellers/rotor blades and other moving parts at
all mes. Keep items that could impact or become entangled away from the propellers/rotor blades including debris, parts, tools,
loose clothing, etc.
Always operate your aircra in open areas that are free from people, vehicles and other obstrucons. Never fly near or above
crowds, airports or buildings.
To ensure proper operaon and safe flight performance never aempt to operate your aircra nearby buildings or other
obstrucons that do not offer a clear view of the sky and can restrict GPS recepon.
Do not aempt to operate your aircra in areas with potenal magnec and/or radio interference including areas nearby
broadcast towers, power transmission staons, high voltage power lines, etc.
Always keep a safe distance in all direcons around your aircra to avoid collisions and/or injury. This aircra is controlled by a
radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
To ensure proper and safe operaon of the automac landing funcon in Home Mode you must start the motors with the aircra
in a posion that has at least 10 feet (approximately 3 meters) of clear and open space around it and achieve a proper GPS lock.
Do not aempt to operate your aircra with any worn and/or damaged components, parts, etc. (including, but not limited to,
damaged propellers/rotor blades, old baeries, etc.).
Never operate your aircra in poor or severe weather condions including heavy winds, precipitaon, lightning, etc.
Always operate your aircra starng with a fully charged baery. Always land as soon as possible aer the first level low voltage
baery warning or land immediately aer the second level low voltage baery warning (as indicated by the vibraons and
audible alerts from the transmier/personal ground staon).
Always operate your aircra when the voltage of the baery in the transmier/personal ground staon is in a safe range (as
indicated by the baery charge status icon on the screen of the transmier/personal ground staon).
Always keep the aircra in clear line of sight and under control, and keep the transmier/personal ground staon powered on
while the aircra is powered on.
Always move the throle control sck down fully and turn off the motors in the event the propellers/rotor blades come into
contact with any objects.
Always allow components and parts to cool aer use before touching them and flying again.
Always remove baeries aer use and store/transport them per the corresponding guidelines.
Avoid water exposure to all electronic components, parts, etc. not specifically designed and protected for use in water. Moisture
causes damage to electronic components and parts.
Never place any poron of the aircra or any related accessories, components or parts in your mouth as doing so could cause
serious injury or even death.
Always keep chemicals, small parts and electronic components out of the reach of children.
Carefully follow the instrucons and warnings included with this aircra and any related accessories, components or parts
(including, but not limited to, chargers, rechargeable baeries, etc.).
CAUTION: The electronic speed controls (ESCs) installed in TYPHOON are not compable with any other product, and
TYPHOON is not compable with any other ESCs. Use of any other ESCs in TYPHOON will cause a crash, which may result in
damage to the product, property and/or cause serious injury.
BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Lithium Polymer (LiPo) baeries are significantly more volale than alkaline, NiCd or NiMH baeries. All instrucons
and warnings must be followed exactly to prevent property damage and/or serious injury as the mishandling of LiPo baeries
can result in fire. By handling, charging or using the included LiPo baery you assume all risks associated with LiPo baeries. If
you do not agree with these condions please return the complete product in new, unused condion to the place of purchase immediately.
You must always charge the LiPo baery in a safe, well-venlated area away from flammable materials.
Never charge the LiPo baery unaended at any me. When charging the baery you must always remain in constant observaon
to monitor the charging process and react immediately to any potenal problems that may occur.
Aer flying/discharging the LiPo baery you must allow it to cool to ambient/room temperature before recharging.
To charge the LiPo baery you must use only the included charger or a suitably compable LiPo baery charger. Failure to do so may
result in a fire causing property damage and/or serious injury.
If at any me the LiPo baery begins to balloon or swell, disconnue charging or discharging immediately. Quickly and safely
disconnect the baery, then place it in a safe, open area away from flammable materials to observe it for at least 15 minutes.
Connuing to charge or discharge a baery that has begun to balloon or swell can result in a fire. A baery that has ballooned or
swollen even a small amount must be removed from service completely.
Do not over-discharge the LiPo baery. Discharging the baery too low can cause damage to the baery resulng in reduced power,
flight duraon or failure of the baery enrely. LiPo cells should not be discharged to below 3.0V each under load.
Store the LiPo baery at room temperature and in a dry area for best results.
When charging, transporng or temporarily storing the LiPo baery the temperature range should be from approximately 40–120°
F (5–49° C). Do not store the baery or aircra in a hot garage, car or direct sunlight. If stored in a hot garage or car the baery can
be damaged or even catch fire.
Never leave baeries, chargers and power supplies unaended during use.
Never aempt to charge low voltage, ballooned/swollen, damaged or wet baeries.
Never allow children under 14 years of age to charge baeries.
Never charge a baery if any of the wire leads have been damaged or shorted.
Never aempt to disassemble the baery, charger or power supply.
Never drop baeries, chargers or power supplies.
Always inspect the baery, charger and power supply before charging.
Always ensure correct polarity before connecng baeries, chargers and power supplies.
Always disconnect the baery aer charging.
Always terminate all processes if the baery, charger or power supply malfuncons.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio
communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful
interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operaon.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE WARNING
This equipment must be installed and operated in accordance with provided instrucons and the antenna(s) used for this transmier
must be installed to provide a separaon distance of at least 20 cm from all persons and must not be co-located or operang in
conjuncon with any other antenna or transmier. End-users and installers must be provide with antenna installaon instrucons
and transmier operang condions for sasfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaon est
autorisée aux deux condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un environnement non contrôlé
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

yuneec-typhoon-q500-4k

Suche zurücksetzen

  • habe immer ein leichtes flimmern bei Video aufnahmen Eingereicht am 2-7-2020 19:12

    Antworten Frage melden
  • Yuneec Typhoon Q 500 4K RtF läßt sich nicht mit ST 12 verbinden.Habe Copter 2 mal um 45 Grad gekippt,um Verbindungs Modus herzustellen,Er sollte dann Gelb blinken,damit neues Modell angelegt und binden kann.Coopter blinkt weiter blau .Keine Bindung möglich.Was kann ich tun? Eingereicht am 19-6-2019 09:39

    Antworten Frage melden
  • Wie vermeide ich Kippen des Q500+ bei der Landung ? Eingereicht am 26-10-2016 14:43

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yuneec Typhoon Q500 4K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Yuneec Typhoon Q500 4K

Yuneec Typhoon Q500 4K Bedienungsanleitung - Englisch - 39 seiten

Yuneec Typhoon Q500 4K Bedienungsanleitung - Französisch - 38 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info