The Turn Le and Turn Right are disabled in this mode (Fly to the Le Direcon and Fly
to the Right Direcon can be controlled). The pilot will always be kept in the frame
wherever he/she moves.
NOTICE: In the Smart Mode, the geo-fence will keep the aircra from traveling further than
295 (90 m). The geo-fence is a virtual 'barrier'.
CAUTION: Any operaon related to camera control needs to be done on mobile APPs. The
APP can be downloaded from Google Play Store or APP Store. You can’t use the Wizard™
to take photos or record videos.
IMPORTANT NOTE: The ‘Point To Fly’ Funcon can only be acvated in Smart Mode.
USER MANUAL
INTRODUCTION
The TYPHOON Wizard™ is a mini GPS tracking device that gives you full one-handed flight
control over the TYPHOON aircra. Features such as 'Follow Me' and 'Watch Me' ensure that
you are in frame in every shot. The ‘point to fly’ funcon allows you to point and click to
reposion your TYPHOON in a very intuive way.
IMPORTANT NOTE: This Quick Start Guide is NOT intended to replace
the content included in the instrucon manual. You should read the instrucon manual
completely before proceeding.
NOTICE: Please find a SD Card in the accessory box. There are tutorial video, electronic user
manual and show case in the SD Card.
TYPHOON WIZARD™ AND RECEIVER BINDING:
NOTICE:
If it is your first me to use the TYPHOON Wizard™ to control an aircra, please
bind the TYPHOON Wizard™ to your aircra.
Step 1) Turn on the aircra. Liits tail upwards approximately 45° then back down
to 'level' twice to put the aircra/receiver into binding mode.
FLIGHT CONTROLS
NOTICE: The safe distance between the TYPHOON Wizard™ and the aircra is 39 (12m).
The TYPHOON Wizard™ can be controlled in different posions. Direcon Control Buons
funcon differently according to the posions of the Wizard™.
‘POINT TO FLY’ FUNCTION
Press and hold the Magic Buon on the TYPHOON Wizard™, and the aircra will fly in the
direcon the TYPHOON Wizard™ is pointed to in the sky.
To Enter ‘Point To Fly’ Funcon
When the aircra is flying, point the TYPHOON Wizard™ to a direcon, press and hold the
Magic Buon. Release the Magic Buon when Aircra Mode LED glows solid blue and
TYPHOON Wizard™ vibrates once. Then the aircra will fly to the direcon the TYPHOON
Wizard™ points. The closer the TYPHOON Wizard™ is lted towards 0°, the further the
aircra will fly away from the pilot. The closer the TYPHOON Wizard™ is lted towards 90°,
the closer the aircra will fly to the pilot. When the Wizard™ is lted at 90°, the aircra will
fly close to you straightly and stop at a safe distance.
NOTICE: The recommended flying height is 33-66 (10-20 m). The operang distance
range of the TYPHOON Wizard™ is 33-164 (10-50 m).
CAMERA CONTROLS
ANGLE MODE
When the Flight Mode Selecon Switch is in the middle posion the aircra will be in Angle Mode.
The Aircra Mode LED will be solid purple.
In this mode, the aircra will move in the direcon the TYPHOON Wizard™ is controlled
relave to the front/nose of the aircra. The aircra has no funcon of Follow Me or Watch Me.
NOTICE: In this mode, the ‘Point To Fly’ Funcon can't be acvated.
IMPORTANT NOTICE: In the Angle mode, the aircra is not suggested travelling further
than 656 (200 m). The Wizard™ will keep vibrang when the aircra travels further than
656 (200 m).
HOME MODE
When the Flight Mode Selecon Switch
is in the boom posion, the aircra will
be in the Home Mode. The Aircra Mode
LED will be solid red. To exit the Home
Mode, switch the Mode Switch to
Angle/Smart Mode, then the aircra will
stop moving and automacally hold its
posion (with a suitable GPS signal/lock)
and maintain a level atude then.
In Home Mode the aircra will fly in a
straight line in the direcon of the pilots'
current locaon, and automacally land
within 13-26 (4-8 m) of the pilot.
2) When the TYPHOON
Wizard™ is lted upwards
between 0° and 40°, the
funcons of the Direcon
Control Buons are as
followed:
1) When the TYPHOON
Wizard™ is lted upwards
between 50° and 90°, the
funcons of the Direcon
Control Buons are as
followed:
NOTICE: When the aircra flies to the le or right side, the nose of aircra doesn't change
its direcon when the TYPHOON Wizard™ is lted upwards between 0° and 40°.
To Exit ‘Point To Fly’ Funcon
When in the‘Point To Fly’ Funcon, press any Direcon Control Buon to exit this
funcon. The aircra will stop moving and automacally hold its posion (with a suitable
GPS signal/lock) and maintain a level atude then.
NOTICE: The TYPHOON Wizard™ only needs to be bound to an aircra for the first me. There
is no need to bind the Wizard™ to the same aircra when you use it again.
Step 2) Press and hold the Power Buon
ll the Aircra Mode LED glows solid
blue. Shake the TYPHOON Wizard™ up
and down ll hearing two beeps from the
aircra. Release the Power Buon.
Any camera control including photo taking or video recording should be operated on
Mobile Apps, which can be downloaded from Google Play Store or APP Store. The detailed
informaon can be referred to relevant User Manuals on the official website: www.
yuneec.com
NOTICE: The control radius range of camera control is within 295 (90 m).
CAUTION: When using the Wizard™, if it keeps vibrang connuously, it indicates the
hardware in the Wizard™ malfuncon. Please send it to the official service center for
maintenance.
NOTICE: In this mode, the ‘Point To Fly’ Funcon can’t be acvated.
WARNING: The maximun flight speed of TYPHOON Q500 aircra is 3.14MPH (7m/s). If
the movement of the pilot is much faster than 3.14MPH (7m/s), the aircra may fly away.
IMPORTANT NOTE: ‘Fly away’ is NOT covered under warranty.
CAUTION: Don’t switch to Home Mode when you are near bodies of water.
2) Follow Me Funcon Under Smart Mode
The Follow Me funcon allows the aircra to
follow the pilot, adjusng its locaon to the
locaon of the TYPHOON Wizard™. All
buons are controllable in this mode. When
in Follow Me funcon, the aircra will follow
the movement of the TYPHOON Wizard™ if
there is no extra operaon on the TYPHOON
Wizard™.
Follow Me funcon can be switched to by
the following steps:
When in Smart Mode, press the Magic
Buon quickly once, it is "follow me" model if
Aircra Mode LED is yellow and Wizard™ GPS
LED is green
GENERAL SAFETY PRECAUTIONS AND WARNINGS
· Failure to use this product in the intended manner as described in instrucon manual can
result in damage to the product, property and/or cause serious injury. This product is not a
toy! If misused it can cause serious body harm and damage to property.
· As the user of this product you are solely and wholly responsible for operang it in a manner
that does not endanger yourself and others or result in damage to the product or the
property of others.
· Do not aempt to operate your equipment in areas with potenal magnec and/or radio
interference including areas nearby broadcast towers, power transmission staons, high
voltage power lines, etc.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC
rules. These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may
cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
This device complies with part 15 of the FCC rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operaon.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modificaons not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may
cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitaon est autorisée aux deux condions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconne-
ment.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an
uncontrolled environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies pour un
environnement non contrôlé
CHARGING THE BATTERIES
BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Lithium Polymer (LiPo) baeries are significantly more volale than alkaline,
NiCd or NiMH baeries. All instrucons and warnings must be followed exactly to prevent
property damage and/or serious injury as the mishandling of LiPo baeries can result in fire.
By handling, charging or using the included LiPo baery you assume all risks associated with
LiPo baeries. If you do not agree with these condions please return the complete product
in new, unused condion to the place of purchase immediately.
• You must always charge the LiPo baery in a safe, well-venlated area away from
flammable materials.
• Never charge the LiPo baery unaended at any me. When charging the baery you
must always remain in constant observaon to monitor the charging process and react
immediately to any potenal problems that may occur.
• Aer flying/discharging the LiPo baery you must allow it to cool to ambient/room
temperature before recharging.
• To charge the LiPo baery you must use only the included charger or a suitably compable
LiPo baery charger. Failure to do so may result in a fire causing property damage and/or
serious injury.
• If at any me the LiPo baery begins to balloon or swell, disconnue charging or
discharging immediately. Quickly and safely disconnect the baery, then place it in a safe,
open area away from flammable materials to observe it for at least 15 minutes. Connuing
to charge or discharge a baery that has begun to balloon or swell can result in a fire. A
baery that has ballooned or swollen even a small amount must be removed from service
completely.
• Do not over-discharge the LiPo baery. Discharging the baery too low can cause
damage to the baery resulng in reduced power, flight duraon or failure of the baery
enrely. LiPo cells should not be discharged to below 3.0V each under load.
• Store the LiPo baery at room temperature and in a dry area for best results.
• When charging, transporng or temporarily storing the LiPo baery the temperature
range should be from approximately 40–120° F (5–49°C). Do not store the baery or
aircra in a hot garage, car or direct sunlight. If stored in a hot garage or car the baery can
be damaged or even catch fire.
• Never leave baeries, chargers and power supplies unaended during use.
• Never aempt to charge low voltage, ballooned/swollen, damaged or wet baeries.
• Never allow children under 14 years of age to charge baeries.
• Never charge a baery if any of the wire leads have been damaged or shorted.
• Never aempt to disassemble the baery, charger or power supply.
• Never drop baeries, chargers or power supplies.
• Always inspect the baery, charger and power supply before charging.
• Always ensure correct polarity before connecng baeries, chargers and power supplies.
• Always disconnect the baery aer charging.
• Always terminate all processes if the baery, charger or power supply malfuncons.
SPECIFICATIONS
Dimensions 5.47 X 1.46 X 0.98 in (139 X 37 X 25 mm)
Weight (with LiPo Baery) 2.52 oz ( 71.5 g )
Compable Aircfra TYPHOON Q500 / Q500+ / Q500 4K / Black / G
Compable Camera CGO2GB / CGO2+ / CGO3
Water Resistant Yes
Working Hours 3.5 h
Built-In LiPo Baery Voltage / Capacity 3.7V 500mAh
NOTICES AND WARNINGS
1. The Wizard™ CAN'T replace the Personal Ground Staon/Remote Controller because it has no Wifi.
2. The Wizard™ is water resistant but NOT waterproof, Do not submerge the Wizard™ in water
even if it is in the waterproof carrying pouch. This will cause the aircra to lose signal.
3. Do not use Home Mode when flying near bodies of water.
4. Be sure to turn off the Wizard™ when you do not use it.
5.Be sure to operate the Wizard™ in open areas that are free from people, vehicles and other
obstrucons. Never fly near or above crowds, airports or buildings.
You can charge the LiPo baery in the
TYPHOON Wizard™ by using supplied
USB cable and inserng it into the USB
port on your computer. Make sure the
TYPHOON Wizard™ is OFF and connect
cable into open USB port on your
computer. The Power LED will show solid
RED while baery is charging, when
charging is completed the red LED light
will turn off. It will take approximately 2
hours to charge a fully discharged baery.
A fully charged baery will give an
operang me of 3.5 hours per charge.
WARNING: Do not take out the LiPo baery installed in the TYPHOON Wizard™, otherwise
the TYPHOON Wizard™ may be damaged.
CUSTOMER SERVICE
YUNEEC EU
24568 Kaltenkirchen, Germany
+49 4191 932620
eusales@yuneec.com
YUNEEC AU
53 Ellemsea Circuit, Lonsdale
South Australia 5160
+61 (0) 8 8186 3301
aussales@yuneec.com
YUNEEC USA
5555 Ontario Mills Parkway,
Ontario, CA91764, USA
1 855 284 8888
sales@yuneec.com
YUNEEC HK
2/F, Man Shung Industrial Building,
7 LaiYipStreet, Kwun Tong,
Kowloon, Hong Kong
852 3616 6071
asiasales@yuneec.com
hp://yuneec.com/support
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two
condions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operaon.
0°
50°
90°
0°
40°
90°
Ascend
Fly Forward
Descend
Fly Backward
Turn Le
Fly to the
Le Direcon
Fly to the
Right Direcon
Turn Right
PILOT LOCATION
13-26 (4-8m)
LANDING
LOCATION
Shake
Smart Circle
WIZARD™ LED STATUS:
Aircra Mode LED
Wizard™ GPS LED
Aircra Status LED
Wizard™ Power LED:
GPS Locked: LED solid green.
The Communicaon Mal-funcon Between the Wizard™ and the Aircra : LED solid red
GPS Loss of Aircra: LED off
Aircra in No-Fly Zone: LED blinking red, green and blue alternately
Baery fullLED solid green
Baery 50%LED blinking green twice every 2 seconds
Baery 25%LED blinking green once every 2 seconds
Low Voltage Warning of the Aircra:
LED blinking red quickly, the Wizard™ vibrang for 2 seconds once connuously
Powered On: LED solid green
During Charging: LED solid red
Charging Completed: Red LED off
Low Voltage Warning of the Wizard™:
Low Baery--- LED blinking green twice every 2 seconds
Low Voltage--- LED blinking green once every 2 seconds
Power Cut-off---LED blinking red quickly, the Wizard™ vibrang for 2 seconds once
connuously.
Smart Mode: LED solid green
Watch Me Funcon: LED solid green
Follow Me Funcon: LED solid yellow
Angle Mode: LED solid purple
Home Mode: LED solid red
‘Point To Fly’ Funcon Acvated: LED solid blue
Anyinformaon above might be changed due to the soware update. For the latest
documents, please check the official website.
When the Aircra Status LED is solid yellow or blinking yellow frequently, it indicates
calibraon is needed. The operaon can be referred to the video of calibraon from our
official website: www.yuneec.com
If there is no proper calibraon, the Point to Fly funcon won't work even when pressing the
magic buon, the Wizard™ will vibrate twice as a warning signal(it only vibrates once in the
normal condion).
OVERVIEW
1. Aircra Mode LED
2. Wizard™ GPS LED
3. Aircra Status LED
4. Ascend / Forward Buon
5. Turn / Fly to the Le Side Buon
6. Turn / Fly to the Right Side Buon
7. Descend / Backward Buon
8. Magic Buon
9. Pitch Control Buon-down
10. Pitch Control Buon-up
11. Start / Stop Motors Buon
12. Wizard™ Power Buon
13. Wizard™ Power LED
14. Smart / Angle / Home Mode Switch
15. Clip
16. USB Port
1
2
3
15
16
4
6
5
8
14
7
109
11
12
13
POWERING ON/OFF:
Press and hold the Power Buon . When all LEDs blink once and the TYPHOON Wizard™
vibrates once, release the Power buon . The Power LED glows solid green, and the Aircra
Mode LED is on, then the TYPHOON Wizard™ is powered on successfully.
NOTICE: Gyroscopes Mal-funcon: If the TYPHOON Wizard™ keeps vibrang when
powering on and fails to power on, please return it to the service center for maintenance.
a
a
b
b
Wizard™ Poinng Direcon
1) Watch Me Funcon Under Smart Mode
Watch Me funcon enables the camera to
keep tracking the TYPHOON Wizard™ no
maer where and how it moves as the
camera can automacally lt its angle
according to the controller. It is "watch me"
model if both the LEDs for Aircra Mode
and Wizard™ GPS are green.
Usually, the default funcon under the
Smart Mode is Watch Me.
FLIGHT MODES
SMART MODE
When the Flight Mode Selecon Switch is in the top posion, the aircra will be in the Smart
Mode. The Aircra Mode LED will glow solid green.
IMPORTANT NOTE: It’s safer and beer for the longevity of the baery to store it only
parally charged for any length of me. Storing the baery approximately 50%, charged
(which is around 3.85V per cell) is typically best, however, it will take some careful
management of the charge me and the use of a volt meter to achieve this voltage. If you
have the equipment and skills to achieve the 50% charge level for storage it is recommend-
ed. If not, simply be sure to not store the baery fully charged whenever possible. In fact, as
long as the baery will be stored at approximately room
temperature and for no more than a few weeks before the next use, it may be best to store
the baery in the discharged state aer the last flight (as long as the baery was not
over-discharged on the last flight).
Brauchen Sie Hilfe? Stellen Sie Ihre Frage.
Missbrauch melden von Frage und/oder Antwort
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yuneec Typhoon Wizard wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
