Bedienungsanleitung Zanussi ZCE 7701 (Seite 30 von 36) (Englisch)

34590

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CLEANING BETWEEN THE OUTER AND

INNER DOOR GLASS PANELS

The outer door panel is removable for cleaning.

TO REMOVE THE OUTER PANEL

1. Open the oven door slightly to gain access to the

two cross head screws on the top of the oven

door.

2. Loosen the two screws using a Pozidrive

screwdriver.

3. Hold the door panel securely in place with one

hand before removing the screws completely with

the other hand.

4. Using both hands, gently tilt the top of the door

glass towards you, lift slightly to disengage the

locators from the two bottom brackets.

5. Clean the outer and inner glass using hot soapy

water or Hob Brite may be used with care. DO

NOT use Hob Brite on the Stainless Steel or

painted finishes. DO NOT try to clean the foil

which is inside the door. The foil is there to help

keep the door cool, if it is damaged it will not

work. Ensure that all parts are well rinsed and

thoroughly dried before attempting to replace the

outer door.

TO REPLACE THE OUTER PANEL

1. Holding the door panel with both hands, gently

place the locators into the holes of the brackets

at the bottom of the oven door.

2. Push the top of the oven glass towards the oven

door, ensuring the screw location holes line up.

3. Hold the panel in place with one hand and insert

the cross head screws into the location holes

with the other hand. Give the screws one turn

to ensure the glass is secure.

4. Tighten the screws positively with a Pozidrive

screwdriver before closing the oven door.

Do not attempt to use the oven without the

glass being in place.

If the door glass panel becomes chipped or

has deep scratches the glass will be

weakened and must be replaced to prevent

the possibility of the panel shattering.

Please contact your local Service Force

Centre who will be pleased to advise further.

TO CLEAN THE INNER GLASS DOOR

PANELS

Clean the inner glass door panels using a soft cloth

and hot water to which a little washing up liquid has

been added. If the inner panel is heavily soiled, Hob

Brite may be used. Do not use abrasive cleaning

materials on the door glass. Ensure that all parts are

well rinsed and thoroughly dried before attempting to

replace the glass.

REPLACING AN OVEN LIGHT BULB

The type of bulb required is a 300°C 25 watt small

Edison Screw. Part number 572 491 5431-00/1

(Available through local Service Force Centres).

CAUTION: DISCONNECT THE APPLIANCE

FROM THE ELECTRICITY SUPPLY BEFORE

REPLACING THE BULB.

Open the door and remove the shelves to enable

easy access to the oven light assembly. Insert a flat

blade screwdriver between the oven side and glass

which covers the bulb.

Support the glass with your hand and prise out

sufficiently to release the glass cover. Unscrew the

bulb in an anticlockwise direction until it is possible to

remove the bulb with ease.

Fit the new bulb by turning in a clockwise direction

until it is secure. Ensuring the indent to the flange is

pointing to the rear of the oven, replace the glass by

pushing it firmly into the hole to cover the bulb

assembly.

Replace the shelves. Restore the electricity supply

and adjust the time of day and clock as necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZCE 7701 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info