Bedienungsanleitung Zanussi ZDF26020XA (Seite 26 von 40) (Englisch, Holländisch)

765948

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

SETTINGS

PROGRAMME SELECTION MODE

In the programme selection mode it is possible to

set a washing programme and to enter the user

mode to change the appliance settings.

To enter the programme selection mode, press on/

off.

The appliance is in programme selection mode

when programme indicator is on and the

display shows the programme duration.

If the control panel does not indicate that the

appliance is in programme selection mode,

implement the Reset procedure.

RESET FUNCTION

Use Reset to:

• Reset the currently running programme.

• Stop the countdown of the Delay option.

• Bring the appliance back to the programme

selection mode.

To Reset, press and hold and until

the appliance is in programme selection mode.

USER MODE

User mode allows to change the following settings:

• Adjust the level of the water softener according

to the water hardness.

• Activate or deactivate the rinse aid empty

notiﬁcation.

• Activate or deactivate AirDry.

Before entering user mode, make sure the

appliance is in programme selection mode:

1. Press and hold and .

• The indicators , and

ﬂash.

As the appliance stores the saved settings, there is

no need to conﬁgure it before every cycle.

ADJUSTING THE WATER SOFTENER

Make sure that the appliance is in user mode:

1. Press .

• The indicators and are off.

• The indicator still ﬂashes.

• The display shows the current setting: e.g.

= level 5.

2. Press to change the setting. Each

pressing increases the level number by one.

After reaching level 10, the countdown starts

again from level 1.

3. Press on/off to conﬁrm the setting.

If you use multi-tabs containing salt

and the hardness of your water is

lower than 21°dH, you can set the

lowest water softener level. It

deactivates the salt reﬁll indicator.

If you use standard detergent or multi-

tabs without salt, set the proper water

hardness level to keep the salt reﬁll

indicator active.

THE WATER HARDNESS TABLE

The water softener removes minerals from the water

supply, which would have a negative effect on the

washing results and on the appliance.

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. It is important to set the right

level of the water softener to assure good washing

results.

Water hardness

German degrees

(°dH)

French degrees

(°fH) mmol/l Clarke de-

grees Water softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDF26020XA Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDF26020XA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info