Bedienungsanleitung Zanussi ZDG 313 X (Seite 5 von 13) (Englisch)

74464

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Instruction for the Installer

The following instructions about installation

and maintenance must be carried out by

qualified personnel in compliance with the

regulation in force. The regulation to be

applied for this type of installation is NBN D

5I.003 : "Installations functioning with

combustible gas lighter than air".

The appliance must be electrically

disconnected before all interventions. If any

electric supply to the appliance is required to

carry out the work, ensure all the necessary

precautions are followed.

The side walls of the unit in which the hob is

going to be installed, must not exceed the

height of the working top.

Avoid installing the appliance in the proximity

of inflammable materials (e.g. curtains, tea

towels etc.).

Gas connection

It is indispensible that the connection to the gas mains

are carried out by means of an AGB tap. Choose fixed

connections or use a flexible pipe in AGB (stainless

steel).

If using flexible metallic pipes, be careful they do not

come in contact with mobile parts or they are not

squeezed. Use the same attention when the hob is

combinated with an oven.

This hob can be operated by Slochteren gas (G25) with

a nominal pressure of 25 mbar or by natural gas with

nominal pressure of 20 mbar. No regulation is required for

use by these two types of gas.

IMPORTANT - To ensure a correct operation, a saving

of energy and the long-life of the appliance, the voltage

pressure of the appliance must correspond to the

recommended values.

A) Ramp with ending nut

B) Seal

C) Adjustable connection

Fig. 2

FO 2365

Gas Burner Rating

Ultra-Rapid Burner 4,0 kW

Class 3 Appliance

Category II2E+3+

Setting Natural Gas G20/G25 - 20/25 mbar

Gas connection G 1/2"

Electric Supply 230 V 50 Hz

Hob recess dimensions

Length 270 mm.

Width 490 mm.

This appliance complies with the following

E.E.C. Directives:

- 73/23 - 90/683 (Low Voltage Directive);

- 89/336

(Electromagnetical Compatibility Directive);

- 90/396 (Gas Appliances)

- 93/68 (General Directives)

and subsequent modifications.

Technical Data

Before fitting the appliance ensure that the installation

has the correct voltage for the appliance. At full capacity,

the drop in pressure must not exceed 5%. Such a drop in

pressure is caused by the following parameters:

- maximum capacity of meter;

- diameter and lenght of the tube in front and behind the

meter;

- section of transit of variuos tubes positioned on the

circuit;

- diameter of eventual connections.

The adjustable connection is fixed to the comprehensive

ramp by means of a threaded nut G 1/2". All the

components shown in Fig. 2 have already been assembled

in the factory.

The appliance, before leaving the factory, has been tested

in order to give you the best results.

IMPORTANT - When the final connection has been

made, it is essential that a thorough leak test is carried

out on the hob and installation. Use some soapy water,

never a flame.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDG 313 X Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDG 313 X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info