Bedienungsanleitung Zanussi ZDI 6895 SX (Seite 12 von 20) (Englisch)

34647

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1. Check the filters

Ensure they are clean and properly positioned (see

"Maintenance and cleaning").

2. Press the On/Off push button

The display will show the last selected programme and

the corresponding phase indicator lights will illuminate.

If the door is open also the "open door" indicator light

will illuminate.

3. Check that there is rinse aid and salt

The corresponding indicator lights will illuminate if

refilling is necessary.

4. Load the dishes

Remove any scraps of food.

Pull the lower basket out and arrange the saucepans,

plates and cutlery in it.

Pull the upper basket out and arrange the plates,

saucers, glasses and cups etc. in it.

Slide the baskets back into the machine.

5. Ensure that the spray arms can

rotate freely

6. Measure out detergent

Add the required amount of detergent into the dispenser.

Important!

If you select the half load option remember to reduce the

quantity of detergent.

Close the detergent dispenser lid.

7. The setting of the programme can

be done both with opened or closed

door

Opened door: select the programme and if necessary

the options (drying options, half load, delay start).

The START push button can be pressed before the

closure of the door (in this case the phase indicator

lights for that programme will turn off, except for the

indicator light of the first phase of the programme that

will flash continuously until the closure of the door).

Close the door and the programme will start

automatically.

Opened door: select the programme and if necessary

the options (drying options, half load, delay start).

Close the door and press the START push button, the

programme will start automatically.

Closed door: select the programme and if necessary

the options (drying options, half load, delay start).

The start of the programme will only occur only after

having pressed the START push button.

8a. Setting and starting the programme

without "delay start"

Press the "SELECTION" push button until the required

programme number appears in the digital display.

Select a drying option and/or half load (if desired).

Press the START push button, an audible signal advises

you that the programme has started.

The display will show the running time of the programme

and the indicator lights of the phases will turn off except

for the indicator light of the current phase.

The time in the digital display will start to decrease from

minute to minute.

Pressing the "SELECTION" push button while the

programme is running will display the number of the

current programme.

If the door is opened during the run of the programme

the current phase will be interrupted and the digital

display will show the number of the programme. The

indicator light of the interrupted phase will start to flash

and the indicator light "open door" will illuminate.

Once the door is closed the programme will start from

the point where it was interrupted.

8b. Setting and starting the programme

with "delay start"

Once a programme and required options (see point 8a)

have been selected to use DELAY proceed as follows:

Press the DELAY push button. The digital display will

show "h 0". Press the button again to select the number

of hours by which you wish to delay the programme start

(up to a maximum of 12 hours).

The delay start will not modify the settings made

previously .

To set the time setting to zero press the DELAY push

button until "h 0" appears in the digital display.

Press the START push button.

The digital display shows the delay time required before

the start of the programme that will decrease from hour

in hour.

The start of the countdown will be confirmed by the

flashing "h" in the digital display.

The phase indicator lights will turn off, only the indicator

lights of the options (drying and/or half load), if selected,

will remain on.

Once the delayed time has elapsed the programme will

start automatically.

If you desire to cancel a delay start in progress follow

the instructions given in the following chapter (point 9).

Operating sequence

152975 55/1 6-08-2002 10:48 Pagina 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDI 6895 SX Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDI 6895 SX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info