Bedienungsanleitung Zanussi ZDLN7531 (Seite 12 von 52) (Englisch, Französisch)

765937

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

AirDry is automatically activated with all

programmes other than Pre-rinse.

CAUTION! Do not try to close the

appliance door within 2 minutes after

automatic opening. This can cause

damage to the appliance.

CAUTION! If children have access to

the appliance, we advise to deactivate

AirDry. The automatic opening of the

door may pose a danger.

When AirDry opens the door, Beam-

on-Floor might not be completely

visible. To see if the programme is

complete, look at the control panel.

KEY TONES

The buttons on the control panel make a click

sound when you press them. You can deactivate

this sound.

LATEST PROGRAMME SELECTION

You can set the automatic selection of the most

recently used programme and options.

The latest programme that was completed before

the appliance deactivation is saved. It is then

selected automatically after you activate the

appliance.

When the latest programme selection is disabled,

the default programme is ECO.

SETTING MODE

How to enter setting mode

You can enter setting mode before starting a

programme. You cannot enter setting mode while

the programme is running.

To enter setting mode, press and hold

simultaneously 30 min and ECO for about 3

seconds.

• The lights related to 60 min, 90 min and

160 min are on.

• The display shows the current value of the

ﬁrst available setting.

How to navigate in setting mode

You can navigate in setting mode using programme

buttons.

CA B

A. Previous button

B. OK button

C. Next button

Use Previous and Next to switch between the

basic settings and to change their value.

Use OK to enter the selected setting and to

conﬁrm changing its value.

How to change a setting

Make sure the appliance is in setting mode.

1. Use Previous or Next to select the desired

setting.

The display shows the current setting value (a digit

and the dedicated letter).

2. Press OK to enter the setting.

The current setting value ﬂashes.

3. Press Previous or Next to change the value.

4. Press OK to conﬁrm the setting.

• The new setting is saved.

• The appliance returns to the basic settings

list.

5. Press and hold simultaneously 30 min and

ECO for about 3 seconds to exit setting mode.

The appliance returns to the programme selection.

The saved settings remain valid until you change

them again.

BEFORE FIRST USE

1. Make sure that the current level of the

water softener agrees with the hardness

of the water supply. If not, adjust the level

of the water softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start the programme 30 min to remove any

residuals from the manufacturing process. Do

not use detergent and do not put dishes in the

baskets.

After starting the programme, the appliance

recharges the resin in the water softener for up to 5

minutes. The washing phase starts only after this

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDLN7531 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDLN7531

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info