Bedienungsanleitung Zanussi ZDSN653X1 (Seite 30 von 44) (Englisch, Holländisch)

765953

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Water softener level Amount of water (l)

1 250

2 100

3 62

4 47

5 25

6 17

7 10

8 5

9 3

10 3

In case of the high water softener setting, it may

occur also in the middle of the programme, before

the rinse (twice during a programme). Regeneration

initiation has no impact on the cycle duration,

unless it occurs in the middle of a programme or at

the end of a programme with a short drying phase.

In that cases, the regeneration prolongs the total

duration of a programme by additional 5 minutes.

Subsequently, the rinsing of the water softener that

lasts 5 minutes may begin in the same cycle or at

the beginning of the next programme. This activity

increases the total water consumption of a

programme by additional 4 litres and the total

energy consumption of a programme by additional

2 Wh. The rinsing of the softener ends with a

complete drain.

Each performed softener rinse (possible more than

one in the same cycle) may prolong the programme

duration by another 5 minutes when it occurs at any

point at the beginning or in the middle of a

programme.

All the consumption values mentioned

in this section are determined in

accordance with the currently

applicable standard in laboratory

conditions with water hardness

2.5mmol/L according to the

2019/2022 regulation (water softener:

level 3).

The pressure and the temperature of

water as well as the variations of the

mains supply can change the values.

How to set the water softener level

Make sure the appliance is in user mode.

1. Press once.

• The indicator continues to ﬂash

and the remaining indicators are off.

• The display shows the current setting: e.g.

= level 5.

2. Press repeatedly to change the setting.

Each pressing of increases the level

number. After reaching the level 10, the count

starts again from level 1.

3. Press the on/off button to conﬁrm the setting.

THE RINSE AID EMPTY NOTIFICATION

The rinse aid helps to dry the dishes without

streaks and stains. It is automatically released

during the hot rinse phase.

When the rinse aid chamber is empty, the rinse aid

indicator is turned on notifying to reﬁll rinse aid. If

the drying results are satisfactory while using multi-

tablets only, it is possible to deactivate the

notiﬁcation for reﬁlling rinse aid. However, for best

drying performance, always use rinse aid.

If standard detergent or multi-tablets without rinse

aid are used, activate the notiﬁcation to keep the

rinse aid reﬁll indicator active.

How to deactivate the rinse aid empty

notiﬁcation

Makes sure the appliance is in user mode.

1. Press twice.

• The indicator continues to ﬂash and the

remaining indicators are off.

• The display shows the current setting.

– = the rinse aid empty notiﬁcation

is activated.

– = the rinse aid empty notiﬁcation

is activated.

2. Press to change the setting.

3. Press the on/off button to conﬁrm the setting.

AIRDRY

AirDry improves the drying results. The appliance

door opens automatically during the drying phase

and remains ajar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDSN653X1 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDSN653X1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info