Bedienungsanleitung Zanussi ZDT 200 (Seite 31 von 88) (Deutsch, Englisch, Holländisch, Französisch)

69909

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Warning! To discard the appliance, follow the

procedure:

• Pull the mains plug out of the socket.

• Cut off the mains cable and mains plug and discard

them.

• Discard the door catch. This prevents the children to

close themselves inside the appliance and endanger

their lives.

Installation

Warning! Make sure that mains plug is

disconnected from the mains socket during

installation.

Important! Obey the instructions in the enclosed template

to:

• Build-in the appliance.

• Install the furniture panel.

• Connect to the water supply and drain.

Install the appliance under a counter (kitchen worktop or

sink).

If a repair is necessary, the appliance must be easily ac-

cessible for the engineer.

Put the appliance adjacent to a water tap and a drain.

For the venting of the dishwasher only water fill, water

drain and power supply cable openings are necessary.

The dishwasher has adjustable feet to allow the adjust-

ment of the height.

Make sure that the water inlet hose, the drain hose and

the supply cable are not kinked or squashed, when you

insert the machine.

Attaching the appliance to the adjacent units

Make sure that the counter below which you attach the

appliance is a safe structure (adjacent kitchen units, cab-

inets, wall).

Adjusting the level of the appliance

Make sure that the appliance is level to close and seal the

door correctly. If the level of the appliance is correct, the

door does not catch on the sides of the cabinet. If the door

does not close correctly, loosen or tighten the adjustable

feet until the appliance is level.

Water connection

Water inlet hose

Connected the appliance to a hot (max. 60°) or cold water

supply.

If the hot water comes from alternative sources of energy

that are more environmentally friendly (e.g. solar or pho-

tovoltaic panels and aeolian), use a hot water supply to

decrease energy consumption.

Connect the inlet hose to a water tap with an external

thread of 3/4”.

Caution! Do not use connection hoses from an old

appliance.

The water pressure must be in the limits (refer to the

chapter 'Technical data'). Make sure that the local water

authority gives you the average mains pressure in your

area.

Make sure that there are no kinks in the water inlet hose

and that the water inlet hose is not squashed or entangled.

Turn the inlet hose to the left or the right to suit the in-

stallation. Fit the locknut correctly to prevent water leaks.

Caution! Do not connect the appliance to new pipes

or pipes that are not used for a long time. Let the

water run for some minutes, then connect the inlet hose.

Water inlet hose with safety valve

The water inlet hose is a double-walled and has an inner

mains cable and a safety valve. The water inlet hose is

under pressure only while the water is running. If there is

a leak in the water inlet hose, the safety valve interrupts

the running water.

Warning! Danger-

ous voltage

Be careful when you connect the water inlet hose:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDT 200 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDT 200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info