Bedienungsanleitung Zanussi zgg 755 alu (Seite 18 von 52) (Deutsch, Englisch, Holländisch, Französisch)

332219

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

connection. The flexible pipe is prepared for ap-

ply when:

– it can not get hot more than room tempera-

ture, higher than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting edges or

corners;

– it can be easily examined in order to check

its condition.

The control of preservation of the flexible pipe

consists in checking that:

– it does not show cracks, cuts, marks of burn-

ings on the two ends and on its full length;

– the material is not hardened, but shows its

correct elasticity;

– the fastening clamps are not rusted;

– expired term is not due.

If one or more defects are visible, do not repair

the pipe, but replace it.

Important! When installation is complete,

make sure that the seal of each pipe fitting is

correct. Use a soapy solution, not a flame!

Injectors replacement (only for Belgium)

1. Remove the pan supports.

2. Remove the caps and crowns of the burn-

er.

3. With a socket spanner 7 remove the injec-

tors and replace them with the ones which

are necessary for the type of gas you use

(see table in Technical Data section).

4. Assemble the parts, follow the same pro-

cedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or dif-

ferent from the necessary pressure, you must fit

an applicable pressure adjuster on the gas sup-

ply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners (only

for Belgium):

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the by-pass

screw position.

The by-pass screw

– If you change from natural gas G20/G25

20/25 mbar to liquid gas, fully tighten

the by-pass screw in.

– If you change from liquid gas to natural

gas G20/G25 20/25 mbar, undo the by-

pass screw approximately 1/4 of a turn

(1/2 of a turn for Triple Crown burner).

Warning! Make sure the flame does not

go out when you quickly turn the knob

from the maximum position to the minimum

position.

Electrical connection

• Ground the appliance according to safety

precautions.

• Make sure that the rated voltage and type of

power on the rating plate agree with the volt-

age and the power of the local power supply.

• This appliance is supplied with a mains ca-

ble. It has to be supplied with a correct plug,

able to support the load marked on the rating

plate. The plug has to be fitted in a correct

socket.

• Any electrical component must be installed

or replaced by the Service Force Centre

technician or qualified service personnel.

www.zanussi.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi zgg 755 alu Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info