Bedienungsanleitung Zanussi ZGG66424 (Seite 12 von 20) (Englisch)

671332

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

INJECTORS REPLACEMENT

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors

and replace them with the ones which are

necessary for the type of gas you use (see

table in "Technical Data" chapter).

4. Assemble the parts, follow the same procedure

backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type of

gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must fit

an applicable pressure adjuster on the gas supply

pipe.

ADJUSTMENT OF MINIMUM LEVEL

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob .

4. With a thin screwdriver, adjust the bypass

screw position (A).

5. If you change:

• from natural gas G20 20 mbar to liquid gas,

fully tighten the bypass screw in.

• from liquid gas to natural gas G20 20 mbar,

undo the bypass screw approximately 1/4

of a turn (1/2 of a turn for Triple Crown

burner).

WARNING! Make sure the flame does

not go out when you quickly turn the

knob from the maximum position to the

minimum position.

ELECTRICAL CONNECTION

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug (if

applicable).

• The appliance must not be connected with an

extension cable, an adapter or a multiple socket.

There is a risk of fire.

• Do not let the power cable to heat up to a

temperature of more than 90° C. The cable

should be guided by means of clamps fixed to

the side of the cabinet, in order to avoid any

contact with the appliance beneath the cooktop.

• Make sure that there is access to the mains plug

after the installation.

Electrical Requirements

Permanent electrical installation must agree with

the latest I.E.E. Regulations and local Electricity

Board regulations. For your own safety the

installation must be done by a qualified electrician

(e.g. your local Electricity Board, or a contractor

who is on the roll of the National Inspection Council

for Electrical Installation Contracting [NICEIC]).

The manufacturer refuses to be

held responsible, if these safety

measures are not abided by.

Supply connections

This hob has to be connected to 220-240 V (~

50/60 Hz ) electricity supply.

The hob has a terminal block which is

marked as follows:

• L — Live terminal

• N — Neutral terminal

• or E — Earth terminal

Before carrying out the connection, make sure:

1. The limiter valve and the electrical system can

take the appliance load (see the rating plate)

2. The supply system is equipped with an efficient

earth connection in compliance with the current

standards and regulations

3. The outlet or omnipolar switch used for

connection is easily accessible with the

appliance installed.

The appliance is supplied with a 3 core flexible

power cable with a 3 amp plug. If it is necessary to

change the fuse, use a 3 amp ASTA-approved (BS

1362) fuse.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGG66424 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGG66424

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info