Bedienungsanleitung Zanussi ZGG76534XA (Seite 12 von 20) (Englisch)

671348

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

CAUTION!

It is important to install the elbow

correctly, with the shoulder on the

end of the thread, fitted to the hob

connecting pipe.

CAUTION!

Failure to ensure the correct

assembly will cause leakage of gas.

CAUTION!

Make sure that the gas supply

pressure of the appliance obeys the

recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes

(copper with mechanical end).

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the

injectors and replace them with the ones

which are necessary for the type of gas you

use (see table in "Technical Information"

chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must

fit an applicable pressure adjuster on the gas

supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).

5. If you change:

• from natural gas G20 20 mbar to liquid

gas, fully tighten the bypass screw in.

• from liquid gas to natural gas G20 20

mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of a turn

for Triple Crown burner).

WARNING!

Make sure the flame does not go out

when you quickly turn the knob from

the maximum position to the

minimum position.

Electrical connection

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug (if

applicable).

• The appliance must not be connected with

an extension cable, an adapter or a multiple

socket. There is a risk of fire.

• Do not let the power cable to heat up to a

temperature of more than 90° C. The cable

should be guided by means of clamps fixed

to the side of the cabinet, in order to avoid

any contact with the equipment beneath the

cooktop.

• Make sure that there is access to the mains

plug after the installation.

Electrical Requirements

Permanent electrical installation must agree

with the latest I.E.E. Regulations and local

Electricity Board regulations. For your own

safety the installation must be done by a

qualified electrician (e.g. your local Electricity

Board, or a contractor who is on the roll of the

National Inspection Council for Electrical

Installation Contracting [NICEIC]).

The manufacturer refuses to be

held responsible, if these safety

measures are not abided by.

Supply connections

This hob has to be connected to 220-240 V (~

50/60 Hz ) electricity supply.

The hob has a terminal block which is

marked as follows:

• L — Live terminal

• N — Neutral terminal

•

or E — Earth terminal

Before carrying out the connection, make sure:

12 www.zanussi.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGG76534XA Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGG76534XA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info