Bedienungsanleitung Zanussi ZGGN645K (Seite 7 von 20) (Englisch)

766180

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

For appliances installed in the Republic of Ireland

please refer to NSAI- Domestic Gas Installation I.S

813 Current Edition Section 7- Permitted Locations

of Appliance.

GAS CONNECTION

WARNING! Any gas installation must

be carried out by a GAS SAFE

Please refer to the technical

instructions on how to adjust the hob

to the gas speciﬁcations on Malta.

This appliance is certiﬁed for Malta.

Make sure that, once the hob is installed, it is easily

accessible for the engineer in the event of a

breakdown.

The manufacturer will not accept liability, should the

above instructions or any of the other safety

instructions incorporated in this instruction booklet

be ignored.

On the end of the shaft, which includes the G 1/2"

threaded elbow, adjustment is ﬁxed so that the

washer is ﬁtted between the components as shown

in the diagram. Screw the parts together without

using excessive force.

A B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Connection to the gas supply should be with either

rigid or semi-rigid pipe, i.e. steel or copper.

The connection should be suitable for connecting

to R 1/2 (1/2 BSP male thread).

When the ﬁnal connection has been made, it is

essential that a thorough leak test is carried out on

the hob and installation.

Make sure that the main connection pipe does not

exert any strain on the hob.

If you use ﬂexible metal pipes make sure that they

agree to ISO 10380 and ISO 10807 standards. Be

careful they do not come in touch with mobile parts

or they are not squeezed. Also be careful when the

hob is put together with an oven.

CAUTION! It is important to install the

elbow correctly, with the shoulder on

the end of the thread, ﬁtted to the hob

connecting pipe.

CAUTION! Failure to ensure the

correct assembly will cause leakage of

gas.

CAUTION! Make sure that the gas

supply pressure of the appliance

obeys the recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes

(copper with mechanical end).

INJECTORS REPLACEMENT

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors

and replace them with the ones which are

necessary for the type of gas you use (see

table in "Technical Data" chapter).

4. Assemble the parts, follow the same procedure

backwards.

5. Attach the label with the new type of gas

supply near the gas supply pipe. You can ﬁnd

this label in the package supplied with the

appliance.

If the supply gas pressure is changeable or different

from the necessary pressure, you must ﬁt an

applicable pressure adjuster on the gas supply

pipe.

ADJUSTMENT OF MINIMUM LEVEL

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).

5. If you change:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGGN645K Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGGN645K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info