Bedienungsanleitung Zanussi ZGH76534XS (Seite 6 von 16) (Englisch)

671590

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

• Disconnect the appliance from the mains

supply.

• Cut off the mains electrical cable close to the

appliance and dispose of it.

• Flat the external gas pipes.

INSTALLATION

WARNING! Refer to Safety chapters.

BEFORE THE INSTALLATION

Before you install the hob, write down the

information bellow from the rating plate. The rating

plate is on the bottom of the hob.

Model .......................................

PNC .........................................

Serial number ...........................

GAS CONNECTION

WARNING! The following instructions

about installation, connection and

maintenance must be carried out by

qualiﬁed personnel in compliance with

standards and local regulations in

force.

Choose ﬁxed connections or use a ﬂexible pipe in

stainless steel in compliance with the regulation in

force. If you use ﬂexible metallic pipes, be careful

they do not come in touch with mobile parts or they

are not squeezed. Also be careful when the hob is

put together with an oven.

Make sure that the gas supply

pressure of the appliance obeys the

recommended values. The adjustable

connection is ﬁxed to the

comprehensive ramp by means of a

threaded nut G 1/2". Screw the parts

without force, adjust the connection in

the necessary direction and tighten

everything.

A B C

A. End of shaft

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

WARNING! It is important to install

the elbow correctly. Make sure that the

shoulder is on the end of the thread.

Then install it on the hob connecting

pipe. Incorrect assembly may cause a

gas leakage.

Liquid gas

Use the rubber pipe holder for liquid gas. Always

engage the gasket. Then continue with the gas

connection.

The ﬂexible pipe is prepared for apply when:

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting edges or

corners;

• it can be easily examined in order to make sure

its condition.

The control of preservation of the ﬂexible pipe

consists in checking that:

• it does not show cracks, cuts, marks of burnings

on the two ends and on its full length;

• the material is not hardened, but shows its

correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not repair the

pipe, but replace it.

WARNING! When installation is

complete, make sure that the seal of

each pipe ﬁtting is correct. Use a

soapy solution, not a ﬂame!

INJECTORS REPLACEMENT

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors

and replace them with the ones which are

necessary for the type of gas you use (see

table in "Technical Information" chapter).

4. Assemble the parts, follow the same procedure

backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGH76534XS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGH76534XS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info