Bedienungsanleitung Zanussi zgs 9831 ictx (Seite 16 von 48) (Deutsch, Englisch, Holländisch, Französisch)

335828

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

If the supply gas pressure is changeable or different from

the necessary pressure, you must fit an applicable pres-

sure adjuster on the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the control knob.

4. With a thin screwdriver, adjust the bypass screw po-

sition. If you change from natural gas 20 mbar to liq-

uid gas, fully tighten the adjustment screw in. If you

change from liquid gas to natural gas 20 mbar, undo

the by-pass screw approximately 1/4 of a turn (1/2 of

a turn for Triple Crown burner).

1 Minimum adjustment screw

5. Make sure the flame does not go out when you quick-

ly turn the knob from the maximum position to the

minimum position.

Electrical connection

• Ground the appliance according to safety precautions.

• Make sure that the rated voltage and type of power on

the rating plate agree with the voltage and the power of

the local power supply.

• This appliance is supplied with a mains cable. It has to

be supplied with a correct plug, able to support the

load marked on the rating plate. The plug has to be fit-

ted in a correct socket.

• Any electrical component must be installed or replaced

by the Service Force Centre technician or qualified

service personnel.

• Always use a correctly installed shockproof socket.

• Make sure that there is an access to the mains plug af-

ter installation.

• Do not pull the mains cable to disconnect the appli-

ance. Always pull the mains plug.

• The appliance must not be connected with an extension

cable, an adapter or a multiple connection (risk of fire).

Check that the ground connection is in conformity with

the standard and regulations force.

• The power cable must be placed in such a way that it

does not touch any hot part.

• Connect the appliance to the mains with a device that

lets to disconnect the appliance from the mains at all

poles with a contact opening width of minimum 3 mm,

eg. automatic line protecting cut-out, earth leakage

trips or fuse.

• None of a parts of the connection cable can not get a

temperature 90 °C. The blue neutral cable must be

connected to the terminal block label with "N". The

brown (or black) phase cable (fitted in the terminal

block contact marked with "L") must always be connec-

ted to the live phase.

Replacement of the connection cable

To replace the connection cable use only H05V2V2-F T90

or equivalent type. Make sure that the cable section is ap-

plicable to the voltage and the working temperature. The

yellow/green earth wire must be approximately 2 cm lon-

ger than the brown (or black) phase wire.

Building In

min. 55 mm

min. 650 mm

830 mm

min. 150 mm

30 mm

480 mm

10 mm

27 mm

3 mm

A - supplied seal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi zgs 9831 ictx Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info