Bedienungsanleitung Zanussi ZGX65414 (Seite 11 von 16) (Englisch)

671329

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

For appliances installed in the Republic of

Ireland please refer to the NSAI- Domestic Gas

Installation I.S. 813 Current Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/

diner or bed sitting room (with a volume greater

than 20 m³), but not in a bathroom or shower

room.

The minimum distance combustible material can

be fitted above the hob in line with the edges of

the hob is 400 mm. If it is fitted below 400 mm

a space of 50 mm must be allowed from the

edges of the hob.

For appliances installed in the Republic of

Ireland please refer to NSAI- Domestic Gas

Installation I.S 813 Current Edition Section 7-

Permitted Locations of Appliance.

Gas Connection

WARNING!

Any gas installation must be carried

out by a GAS SAFE REGISTER

installer.

Make sure that, once the hob is installed, it is

easily accessible for the engineer in the event of

a breakdown.

The manufacturer will not accept liability, should

the above instructions or any of the other safety

instructions incorporated in this instruction

booklet be ignored.

On the end of the shaft, which includes the G

1/2" threaded elbow, adjustment is fixed so that

the washer is fitted between the components as

shown in the diagram. Screw the parts together

without using excessive force.

A B C

A) End of shaft with nut

B) Washer

C) Elbow

Connection to the gas supply should be with

either rigid or semi-rigid pipe, i.e. steel or

copper.

The connection should be suitable for

connecting to R 1/2 (1/2 BSP male thread).

When the final connection has been made, it is

essential that a thorough leak test is carried out

on the hob and installation.

Make sure that the main connection pipe does

not exert any strain on the hob.

If you use flexible metal pipes make sure that

they agree to ISO 10380 and ISO 10807

standards. Be careful they do not come in touch

with mobile parts or they are not squeezed. Also

be careful when the hob is put together with an

oven.

CAUTION!

It is important to install the elbow

correctly, with the shoulder on the

end of the thread, fitted to the hob

connecting pipe.

CAUTION!

Failure to ensure the correct

assembly will cause leakage of gas.

CAUTION!

Make sure that the gas supply

pressure of the appliance obeys the

recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes

(copper with mechanical end).

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the

injectors and replace them with the ones

which are necessary for the type of gas you

use (see table in "Technical Information"

chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must

fit an applicable pressure adjuster on the gas

supply pipe.

www.zanussi.com 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGX65414 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGX65414

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info