Bedienungsanleitung Zanussi ZGX66424 (Seite 10 von 28) (Französisch)

671346

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation

WARNING!

Refer to Safety chapters.

Before the installation

Before you install the hob, write down the

information bellow from the rating plate. The

rating plate is on the bottom of the hob.

Model .......................................

PNC .........................................

Serial number ...........................

Gas Connection

WARNING!

The following instructions about

installation, connection and

maintenance must be carried out by

qualified personnel in compliance

with standards and local regulations

in force.

Choose fixed connections or use a flexible pipe

in stainless steel in compliance with the

regulation in force. If you use flexible metallic

pipes, be careful they do not come in touch with

mobile parts or they are not squeezed. Also be

careful when the hob is put together with an

oven.

Make sure that the gas supply

pressure of the appliance obeys the

recommended values. The

adjustable connection is fixed to the

comprehensive ramp by means of a

threaded nut G 1/2". Screw the

parts without force, adjust the

connection in the necessary

direction and tighten everything.

A B C

A) End of shaft with nut

B) Washer

C) Elbow (if needed)

Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue with

the gas connection.

The flexible pipe is prepared for apply when:

• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting edges or

corners;

• it can be easily examined in order to make

sure its condition.

The control of preservation of the flexible pipe

consists in checking that:

• it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

• the material is not hardened, but shows its

correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not repair

the pipe, but replace it.

WARNING!

When installation is complete, make

sure that the seal of each pipe fitting

is correct. Use a soapy solution, not

a flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the

injectors and replace them with the ones

which are necessary for the type of gas you

use (see table in "Technical Information"

chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type

of gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must

fit an applicable pressure adjuster on the gas

supply pipe.

10 www.zanussi.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZGX66424 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZGX66424

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info