Bedienungsanleitung Zanussi ZHC 590 (Seite 17 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

101193

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

GB 17

Extraction

The cooker hood is more effective when used in the extraction mode (ducted to the outside).

Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent

of Ø125mm (5”) or Ø150mm (6”).

For the best performance use the shortest possible duct run and the minimum number of bends.

Where ﬂ exible ducting is ﬁ tted it should not be turned through very tight bends as this may impair the perform-

ance of the hood.

It is recommended a maximum length of 3 metres with one bend, to be installed, to be reduced metre for each

90o bend.

If a distance is greater than 3 metres the efﬁ ciency of the hood could be impaired.

The ducting used must be manufactured from ﬁ re retardent material conforming to the relevant British Standard

or DIN 4102-B1.

When the cooker hood is ducted to the outside the charcoal ﬁ lter must be removed.

INSTALLING THE COOKER HOOD

Installation of components in recycling version:

• Fix the recycling air outlet piece 15 to the upper part

of the frame using four 12c screws supplied with the

hood.

• Fix the ﬂ ange (ø120) 10 to the lower part of the recycling

air outlet 15.

• Put the reducer ﬂ ange 9 on the hood body outlet.

• At this point, join the ﬂ anges with a pipe. In order to

calculate the height of the pipe it is necessary to estimate

the height of the hood (mm) and subtract 615 mm. (H

pipe = H hood-615).

• Lengthen the frame so that the pipe can be inserted.

Place the pipe between the two ﬂ anges and block it. Make

sure that the height of the frame is correct considering

the height of the cooker hood (H frame = H hood – 184).

Adjust the height of the frame and tighten again the earlier

removed screws. Tighten again the safety screws in order

to give more stability to the structure.

• Fix the pipe with the pipe clamps 25 supplied with the

hood.

• Lift the frame up, making sure that the index over the

frame plate is turned backwards.

• Fit the frame slots onto the two screws inserted in the

ceiling as above, and turn until reaching the centre of

the adjustment slot.

• Tighten the two screws and fasten the other two screws

provided; before locking the screws completely, it is

possible to adjust the frame by turning it, making sure

that the screws do not come out of their housing in the

adjustment slot.

12c

• The Frame must be securely fastened so as to support both the weight of the Hood and the stress

caused by occasional axial pressure against the ﬁ tted Appliance. After ﬁ xing, make sure that the base

is stable even when the Frame is subjected to lateral stress.

• If the Ceiling is not strong enough in the area where the hood is to be ﬁ xed, the Installer must strengthen

the area using suitable plates and counterplates anchored to resistant structures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZHC 590 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info