Bedienungsanleitung Zanussi zkf 65 l (Seite 20 von 64) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

333113

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

When building in ceramic glass cooking areas the front

cross-rail of the build-in cupboard must be removed in

order to have the heat radiating off es cape without any

obstacles.

The space under the hob unit must be closed at all

sides in a way that the lower side of the cooking area

is no longer accessible.

The distance from the hob to the furniture part under

the hob must at least amount to 20 mm. If needed,

please fix an insulation. Drawers must not be located

under a hotplate.

The distance from the hob to a high cupboard beside

right or left must at least amount 55 mm, to the back

wall at least amount 55 mm.

With regard to the protection against overheating o f

surrounding furniture surfaces this appliance corres-

ponds to type Y (EN 60335). This appliance or the

built--in cupboard for the appliance respectively may b e

located with the rear wall and one side wall to whatever

high walls or furniture respectively and with the other

side to another appliance o r furniture of the same

height as this appliance.

Built-in dimensions

The opening in the worktop must correspond to com-

mercial dimensions. The hints required are given in the

dimension sketch.

Built-in

Cut out the worktop acc. to prescribed cutout size. The

tolerance sizes must not be exceeded. Do precisely

saw at the mark line. Recommendation: Mark the cut-

out with a steel needle. Glue something on the line in

order to avoid shattering of the coat when cutting.

With tile--coated worktop areas the slits in the support-

ing area for the cooking area must be filled up com-

pletely.

Clean the worktop in the cutout area

From the top lay the cooking area i nto the cutout, adjust

concentrically and firmly press down.

Check the sealing in the supporting frame for perfect

seating and resting without a gap. Please do not apply

additional silicone sealing material, the closure will

make it har der to dismantle in case of need for service.

5 holes in the bottom of the build--in case are provided

for the screws of the fitting plates.

At first screw on the fitting plates by a screwdriver and

afterwards regularly tighten the plates alternatively and

diagonally offset

, until the frame of the cooking area is

perfectly laying on the worktop.

A too strong and one--sided tightening is to be avoided!

Electric screwdrivers or pusher airscrews to be exclu-

sively used with slip clutch (setting value 1 -- 1.1 Nm).

Worktop opening:

width: 560 mm

depth: 490 mm

radius: 5 mm

Appliance:

width: 572 mm

depth: 502 mm

heigth : 49 mm

Voltage: AC 230 V 50 Hz/60 Hz

Total connected load: 5.9 kW

572

502

heigth of the hob

49 mm

heigth of frame

over worktop

3mm

Frame measurement

on worktop 9 mm

hobs frame

ceramic glass plate

fixing clamp

4 Points for fixing clamps

Measurement of

490 ±1560 ±1

49 mm

worktop

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi zkf 65 l Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi zkf 65 l

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info