Bedienungsanleitung Zanussi ZOU20612XU (Seite 4 von 20) (Englisch)

766013

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Width of the back of

the appliance

558 mm

Depth of the appliance 561 mm

Built in depth of the

appliance

540 mm

Depth with open door 1007 mm

Ventilation opening

minimum size. Opening

placed on the bottom

rear side

560x20 mm

Mounting screws 4x25 mm

Before you install the appliance, ﬁt it with the

applicable hob from the table.

Type Maximum power

ZEE 6041 7000 W

ZEV 6040 6000 W

ZEV 6041 6400 W

ZEV 6046 7600 W

ELECTRICAL CONNECTION

WARNING! Risk of ﬁre and electric

shock.

• All electrical connections should be made by a

qualiﬁed electrician.

• The appliance must be earthed.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Do not let mains cables touch or come near the

appliance door or the niche below the

appliance, especially when it operates or the

door is hot.

• The shock protection of live and insulated parts

must be fastened in such a way that it cannot be

removed without tools.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• If the mains socket is loose, do not connect the

mains plug.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type fuses

removed from the holder), earth leakage trips

and contactors.

• The electrical installation must have an isolation

device which lets you disconnect the appliance

from the mains at all poles. The isolation device

must have a contact opening width of minimum

3 mm.

• This appliance is supplied without a main plug

and a main cable.

• The hob connection socket is at the top of the

oven cabinet. The hob has connection leads for

the cooking zones and the ground cable. The

leads have plug-in connectors. Plug the

connectors into the correct oven socket to

connect the hob to the oven. The design of the

plugs and sockets prevents incorrect

connections.

If the mains voltage is different, rearrange the

jumpers on the terminal board (refer to the

connection diagram below). Connect the ground

cable to the terminal. After you connect the supply

cable to the terminal board, attach it with a junction

clamp.

Connecting to terminal board

The appliance has a six-pole terminal board.

The jumpers (bridges) are set for operation on

a 400 V three-phase with a neutral wire.

1 = 45 mm

2 = 45 mm

3 = 60 mm

4 = 60 mm

= 70 mm

1 2 3 4 5

L 1 – 2 – 3 = phase cables

N 4 = neutral cable

= earth cable

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZOU20612XU Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZOU20612XU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info