Bedienungsanleitung Zanussi ZSLN2321 (Seite 10 von 24) (Englisch)

765960

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

German degrees

(°dH)

French degrees

(°fH) mmol/l Clarke de-

grees Water softener level

<4 <7 <0.7 < 5 1 2)

1) Factory setting.

2) Do not use salt at this level.

Regardless of the type of detergent used, set

the proper water hardness level to keep the

salt reﬁll indicator active.

Multi-tabs containing salt are not

effective enough to soften hard water.

Regeneration process

For the correct water softener operation, the resin

of the softener device needs to be regenerated

regularly. This process is automatic and is the part

of the normal dishwasher operation.

When the prescribed quantity of water (see values

in the table) has been used since the previous

regeneration process, a new regeneration process

will be initiated between the ﬁnal rinse and the

programme end.

Water softener level Amount of water (l)

1 250

2 100

3 62

4 47

5 25

6 17

7 10

8 5

9 3

10 3

In case of the high water softener setting, it may

occur also in the middle of the programme, before

the rinse (twice during a programme). Regeneration

initiation has no impact on the cycle duration,

unless it occurs in the middle of a programme or at

the end of a programme with a short drying phase.

In such cases, the regeneration prolongs the total

duration of a programme by additional 5 minutes.

Subsequently, the rinsing of the water softener that

lasts 5 minutes may begin in the same cycle or at

the beginning of the next programme. This activity

increases the total water consumption of a

programme by additional 4 litres and the total

energy consumption of a programme by additional

2 Wh. The rinsing of the softener ends with a

complete drain.

Each performed softener rinse (possible more than

one in the same cycle) may prolong the programme

duration by another 5 minutes when it occurs at any

point at the beginning or in the middle of a

programme.

All the consumption values mentioned

in this section are determined in line

with the currently applicable standard

in laboratory conditions with water

hardness 2.5mmol/L (water softener:

level 3) according to the regulation:

UK Ecodesign 2021/745.

The pressure and the temperature of

water as well as the variations of the

mains supply can change the values.

THE RINSE AID LEVEL

The rinse aid helps to dry the dishes without

streaks and stains. It is automatically released

during the hot rinse phase. It is possible to set the

released quantity of rinse aid.

When rinse aid chamber is empty, the rinse aid

indicator is on notifying to reﬁll rinse aid. If the

drying results are satisfactory while using multi-

tablets only, it is possible to deactivate the

dispenser and the indicator. However, for best

drying performance, always use rinse aid and keep

the rinse aid indicator active.

To deactivate the rinse aid dispenser and indicator,

set the level of rinse aid to 0.

END SOUND

You can activate an acoustic signal that sounds

when the programme is completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZSLN2321 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info