Bedienungsanleitung ZCS 9L2BL (Seite 28 von 36) (Englisch)

517530

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

User’s manual

Restarting

Before restarting the robot after a long period of inactivity, proceed as

follows.

1. Connect the plug of the power supply unit (A) to the electrical outlet.

2. Reconnect the main electrical power supply.

3. Place the robot inside the charging station.

4. Press the ON key (A).

5. Enter the password (if prompted) (See “Password Entry”).

6. After a few seconds, the message “CHARGING” will appear on the

display.

7. At this point, the robot is ready to use (see “Programming Mode”).

Current power

supply unit (A)

Charging

station (C)

BATTERY CHARGING AFTER PROLONGED INACTIVITY

Recharge the battery at least every ﬁ ve months if using lithium batteries.

Danger - Attention

Do not recharge the robot in explosive and ﬂ ammable

environments.

1. Supply electricity to the charging station and make sure the plates are

clean.

2. Position the robot inside the charging station.

3. Press the “ON” key (A).

4. Enter the password (if prompted) (See “Password Entry”).

5. After a few seconds, the message “CHARGING” will appear on the

display.

6. Press the “Start/Pause” key (B). The batteries start the charging cycle.

7. At the end of the charging cycle (approx. 6 hours), press the “OFF/

STOP” key (C).

8. Store the robot in a protected and dry location with an ambient

temperature between 10° and 25° C, out of reach of children, domestic

animals, etc.

“ON” KEY (A)

“START/PAUSE” KEY (B)

“OFF/STOP” KEY (C)

OPERATING TIPS

Below are some useful operating tips to follow when using the robot.

Even after being suitably informed on the use of the robot, simulate some test manoeuvres on ﬁ rst use to identify the commands and main

functions.

Check and secure the fastening screws of the main components.

Mow the lawn frequently to avoid excessive growth of the grass.

Do not use the robot to mow grass that is 1 cm (0,40 ") shorter than the cutting blade.

If the lawn is equipped with an automatic sprinkler system, program the robot to return to the charging system at least one hour before the

sprinklers are turned on.

Check the slope of the ground and make sure the maximum values allowed are not exceeded in order to prevent damage to the robot and

the sprinklers.

We recommend programming the mower so that it does not work more than is necessary, also taking into consideration the different growth

rates of the grass in different seasons, so as not to subject it to unnecessary deterioration and reduction of the battery life.

When using the robot make sure the work area is clear of people (in particular children, the elderly or disabled people) and domestic animals

in order to prevent safety risks. To minimize chance of injury, operate the robot during times when the yard is not being used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZCS 9L2BL Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ZCS 9L2BL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info