Bedienungsanleitung Zelmer 23Z011 (Seite 62 von 64) (Englisch, Polnisch)

538920

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

REMOTE CONTROLLER

12. Set on/off time indicator or current time.

13. Preset temperature indicator.

14. Cooling mode: COOL.

15. Dehumidifying mode: DRY.

16. Heating mode: HEAT- inactive in this model

17. Ventilation mode FAN.

18. Mode selection button. Each time you press the button the mode

will change in the following order: COOL, DRY, FAN.

19. TIMER button.

Used to set the time of the automatic switch on / switch off of the

appliance. When pressed together with the HOUR (27) button, al-

lows to set the time in the 1–12 hour range with an hourly break.

20. Keypad HOLD button.

21. FAN SPEED button. Changes the fan speed from HIGH, MED to

LOW.

22. SLEEP button – inactive in this model.

23. HOLD indicator.

24. TEMP button. Each time you press the button the temperature

will change by 1°C.

25. ON/OFF button.

26. MIN button. Used to set the current time in minutes.

27. HOUR button. Used to set the current time in hours and the auto-

matic switch on/switch off time in hours.

28. SWING button. Used to set the air delivery swing mode (left-right)

or the xed direction mode of air delivery.

29. LAMP button – inactive in this model.

30. CLEAN button – inactive in this model.

Technical specication of the remote controller

Rated voltage 3,0 V

Lowest voltage of CPU emitting signal 2,0 V

Signal receiving range 8 m

Setting the current time

Properly insert two AAA batteries in the battery compartment on the back of the remote controller (see picture).

After installing the batteries the remote controller will automatically set the time to: 0:00.

For instruction purposes, the time will be set to 10:15.

1. Press and hold the HOUR (27) for about 3 seconds. The time indicator will begin to ash.

2. Keep pressing the HOUR (27) button until 10 a.m. is set.

3. Press the MIN (26) button, the minute indicator will begin to ash. Keep pressing the button until it is set to 15.

4. Press the ON/OFF (25) button to conrm the set time. The set time will be automatically cancelled if the ON/OFF

(25) button is not pressed within 15 seconds.

AIR CONDITIONER FUNCTIONS

The air conditioner has three functions: COOL, DRY and FAN ventilation.

The temperature range for the cooling mode is from 17°C to 31°C, and for the dehumidifying mode is from 20°C to 31°C.

Power source

Plug the appliance only to a grounded AC socket connected to a protection circuit. ●

Do not connect the appliance to a multiple socket outlet which is also being used for other electrical appliances. ●

Insert the plug into a power source. After 2 seconds you will hear a beep. Press the ● ON/OFF (H) button on the control panel or the ON/

OFF (25) button on the remote controller for the appliance to start operating.

Cooling operation

1. Repeatedly press the MODE (D) button on the control panel or the MODE (18) button on the remote controller and choose the cooling

mode. The LCD display should show the COOL indicator. During the cooling operation always place the air inlet and hot air exhaust hose

outside the room e.g. through an open window.

2. Repeatedly press TEMP+ or TEMP- (C) button on the control panel or the TEMP (24) button on the remote controller to select the de-

sired room temperature at 17 – 31.

3. Press the FAN SPEED (B) button on the control panel or the FAN SPEED (21) button on the remote controller to select the desired fan

speed: HIGH, MED, or LOW.

4. Press the SWING (E) button on the control panel or the SWING (28) button on the remote controller to adjust the air delivery direction.

When the LCD display shows the symbol SWING ; the swing mode is set (left-right). Otherwise the xed direction mode of air delivery

will be set.

The upper and lower swinging ns (4) can be manually adjusted before the start of operation.

ATTENTION: In order to improve the cooling efciency follow the instructions below:

1. Draw the curtains if the room is directly exposed to the sun.

2. Do not place the air conditioner near other heat sources.

Dehumidifying operation

1. Keep the windows and doors closed for an effective dehumidifying operation.

2. Repeatedly press the MODE (D) button on the control panel or the MODE (18) button on the remote controller and choose the dehumidi-

fying mode. The LCD display will show the DRY indicator.

During the dehumidifying mode the fan speed cannot be adjusted. (The FAN SPEED button is inactive).

3. While using the dehumidifying mode the air conditioner can operate without the air outlet hose.

Open

the back cover

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 23Z011 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info