Bedienungsanleitung Zelmer 32Z011 (Seite 27 von 30) (Englisch, Polnisch)

539093

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Arrange the power supply cord, so that it is not hanging down

the table or counter and it could not be pulled or fastened.

Connect the plug of the power supply cord to the power

supply outlet.

Make sure, that before connecting the appliance to the power

supply, the speed control knob (4) is set in position 0.

Assemble the blender jug (3) on the motor unit, so that

the symbol on the motor unit (8) is in line with the mark

▼on the jug.

Lock the blender jug (3) turning it in clockwise direction,

so that the symbol on the motor unit (8) is in line with the

mark ▼on the jug.

The handle of the blender jug (3) shall be placed on the

right side of the appliance.

Put the ingredients into the blender jug (3).

Do not ll over 1500 ml mark on the blender jug (3).

If you do so, the ingredients can lift the lid (5) when the motor

is started.

Before use of the stand blender, insert the lid (5) onto

the blender jug (3) so, that its protrusion is in line with the

protrusion on the jug.

ATTENTION: Before inserting the lid (5) moisturize the

gasket with water.

Insert the lid overlay (1) into the inlet in the lid (5) so, that

the protrusions of the overlay enter the cuts in the lid inlet

and turn it left or right until it moves.

Do not start up the stand blender without the lid

overlay (1), especially when solid ingredients shall be

used. They can be ejected through the inlet.

Switch on the mixing by turning the speed control

knob (4) to adequate position (P, I, II).

In order to stop the appliance turn the speed control knob

to position 0.

P (PULSE) functions

Turning the knob into

●

P (PULSE) position shall cause the

short operation of the appliance with maximum speed for

the time of holding the knob.

Do not operate the appliance for longer than 2 minutes,

●

otherwise it can be overheated.

In case you need to add some ingredients during the

●

stand blender operation, turn and lift the lid overlay (1),

insert new ingredients through the inlet, then replace the

lid overlay (1) and turn it right until it moves.

Make sure, that the added ingredients shall not exceed

●

the volume inside the jug over 1500 ml mark on the

blender jug (3).

After operation

In order to stop the appliance, turn the speed control knob

to position 0.

Hold the motor unit

●

(8) with one hand, catch the jug

handle with the other hand and remove it out of the

motor unit (8) turning it counter-clockwise.

Remove the lid

●

(5) out of the blender jug (3).

Unplug the appliance from the mains supply when not

●

in use.

Cleaning and maintenance (Fig. C)

Clean after operation as soon as possible, to prevent

the pulp accumulation inside the jug (3).

Pour approximately 1 liter of water to the blender jug (3)

and start-up the appliance for approximately 30 seconds and

hold the P (PULSE) button.

Then empty the blender jug (3), turn it upside-down and

dry.

If necessary, clean the jug (3), lid (5), feeder opening

stopper (1) and blades (6) in warm water with wash-up liquid.

Then rinse it under clean running water and dry.

●

If you left the jug for longer time without cleaning and

●

some particles glued to the jug inner, use nylon brush.

We do not recommend cleaning the jug

●

(3), blades (6),

lid (5) and feeder opening stopper (1) in dish washer.

Aggressive cleaning agents applied in such device can

inuence negative the surface conditions.

Clean the outsider of the motor housing (8) with damp,

gentle cloth.

ATTENTION: Do not immerse the motor housing (8) in

water or other liquid.

Do not clean the outside of the housing

●

(8) with

aggressive detergents such as emulsion milk or pastes,

etc. They can remove information graphic symbols.

Do not clean the transparent jug

●

(3) with harsh sponges

or clothes.

After washing dry thoroughly all the parts of the

●

appliance.

Disassembling of cutting unit

Remove the plug of the power supply cord from the

●

mains supply outlet.

Empty the blender jug

●

(3).

Remove the lid

●

(5) from the blender jug (3). Turn the

blender jug (3) „upside down” and place on the at and

rm surface.

Hold the blender jug

●

(3) with one hand, and unscrew the

blade unit with the other hand (counter-clockwise).

Carefully remove the blade unit

●

(6) including the

gasket (7).

ATTENTION: The appliance blades are sharp. Handle

them carefully.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 32Z011 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info