Bedienungsanleitung Zelmer 32Z013 (Seite 27 von 30) (Englisch, Polnisch)

539095

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Handling and operation (Fig. B)

Preparation for operation

Before rst operation of the jug blender (or operation after

longer storage time), clean the blender jug (3), lid (5) and

lid overlay (1) in warm water with dish washing liquid, rinse

them well and dry. Keep your hands far from the blades –

they are sharp.

Instructions for use

Place the motor unit (10) on dry, rm, horizontal surface,

near the mains supply outlet and out of the children access.

Arrange the supplying cord so, that it does not hang out of the

table or counter to avoid risk of being pulled or caught on.

Connect the plug to the mains supply outlet.

Before you connect the appliance to the power,

make sure that the speed control knob (4) is set in 0

position.

Assemble the blender jug (3) on the motor unit, so that

the symbol on the motor unit (10) is in line with ▼mark

on the jug.

Lock the blender jug (3) rotating it in clockwise direction

so that the symbol on the motor unit (10) is in line with

▼mark on the jug.

The handle of the blender jug (3) should be located on

the right side of the appliance.

Insert the ingredients into the jug (3).

Do not load over the 1000 ml mark on the jug (3).

In such case, the content can lift the lid (5) when the motor

starts up

Before you use the jug blender, insert the lid (2) on the

blender jug (3).

Lock the lid (2) on the blender jug (3) rotating it in

clockwise direction until it moves.

Insert the lid overlay (1) into the lid inlet (5).

Don’t start the jug blender without the lid overlay (1),

especially, when solid ingredients shall be used. They

can be ejected through the lid inlet.

Switch on mixing turning the speed control knob (4) to

appropriate position (pulse, 1, 2, 3).

In order to stop the appliance turn the speed control knob

to 0 position.

Pulse function

Turning the knob to

●

pulse position shall cause a short

operation of the appliance with maximum speed, for the

time you hold the knob.

Do not use it longer than 2 minutes, otherwise it can get

●

overheated.

When you need to add some ingredients during

●

operation of the jug blender, lift the lid overlay (1), insert

new ingredients into the inlet, and replace the lid overlay

(1) again.

Make sure, that the ingredients you add, shall not

●

increase the volume of the ingredients over the 1000 ml

mark on the blender jug (3).

Attachment for centrifuging juice

of soft fruit and soya beans (Fig. C)

The attachment (7) is used for centrifuging juice out of soft

fruit; it can be also applied for preparing soya milk.

It is not allowed to use fruit with stones without prior

pitting them.

Insert the attachment (7) into the blender jug (3) so, that

the runners inside the blender (3) get through the cut-outs in

the bottom ange of the attachment (7).

Lock the attachment (7) rotating it in clockwise direction

until it moves.

Insert the lid (5) on the blender jug (3) and lock it rotating

it in clockwise direction until it moves.

Add the fruit through the inlet in the lid and mix it until you

obtain desired result.

REMARK: Please remember to observe the maximum

operation time for the appliance.

In case the fruit has a small amount of pulp, we

recommend adding liquids, i.e. water, juice during

centrifuging.

In case of preparing soya milk, pour approx. 500 ml of

●

water and 350 g of soaked soya beans through the inlet

in the lid.

After operation

In order to stop the appliance, turn the speed control knob

to position 0.

Hold the motor unit

●

(10) with one hand, catch the jug

handle with the other hand and remove it out of the

motor unit (10) turning it counter-clockwise.

Remove the lid

●

(5) out of the blender jug (3).

Unplug the appliance from the mains supply when not

●

in use.

Cleaning and maintenance

Clean after operation as soon as possible, to prevent

the pulp accumulation inside the jug (3).

Pour approximately 1 liter of water to the blender jug

●

(3)

and start-up the appliance for approximately 30 seconds

and hold the pulse button.

Then empty the blender jug

●

(3), turn it upside-down

and dry.

If necessary, clean the jug

●

(3), lid (5), feeder opening

stopper (1) and blades (6) in warm water with wash-up

liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 32Z013 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info