540093

Zelmer 39Z017 Seite 28

28
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
28 GW39-008_v01
Outline and parts of the hair clipper (Fig. A)
1
Cutting head
2
Cutting length adjustment knob
3
On/OFF switch
4
LCD display
5
Battery rechargeable
6
Loading socket
7
Attachments (4-6; 10-12; 16-18; 22-24; 28-30 mm)
8
Power supply
9
Cleaning brush
10
Lubricating oil for blades
11
Comb
12
Scissors
LCD display
A
percentage charging level indicator
B
graphical battery charging level indicator
C
mains supply connection indicator
Handling and operation of hair clipper
OPERATION WITH POWER SUPPLY ADAPTOR
At rst insert the adaptor plug into the device and then
insert the adapter plug into the mains supply outlet. In mains
supplied mode the device is ready for use.
LOADING ACCUMULATORS AND CORDLESS
OPERATION
Load the device minimum 16h before rst usage and
when 2–3 next loadings.
Make sure the appliance is switched off before charging.
●
The process of battery (installed in the trimmer) charging
●
lasts approximately 2 hours.
The trimmer can work approx. 60 minutes with fully
●
charged batteries.
Insert the ending of the power supply to the trimmer –
charging socket (6),
Insert the plug of the power supply in the mains –
supply outlet. The percentage and graphical
charging level indicators show the charging process
advancement (ashing).
When the battery is fully charged, the LCD display
●
(4)
indicates 100 and it is highlighted in blue.
When the battery charging level decreases below 20, the
●
graphical battery charging level indicator (B) and mains
supply connection indicator (C) start ashing.
When the battery is almost empty, the display colour
●
changes into red. Connect the trimmer to the mains supply.
The hair clipper accumulator obtains optimum power
●
after three cycles of loading and unloading. Ten hours
is enough for next loading. In order to provide long life
of accumulators, they should be completely unloaded
before loading.
COMB ATTACHMENTS INSERTING / REPLACING
Select the attachment according to the length of cutting.
●
Insert appropriate attachment into the sides of the device.
●
The protrusions shall be locked inside small holes (see
the gure beside) on left and right sides.
Replace one attachment removing it and inserting
●
another as described above.
In order to remove an attachment bent one side of assembled
attachment gently and then move it up.
Move the cutting length adjustment knob
●
(2), to increase/
reduce the hair cutting length. The possible hair cutting
length is indicated on each attachment (i.e. 4–6 mm).
USING THE TRIMMER FOR HEAR CUTTING
Cut the hair for demanded length in stages, start form
bigger length.
Insert an appropriate attachment
●
(7).
Set the desired length of hair/beard cutting with cutting
●
length adjustment knob (2).
Start up the hair clipper pressing in ON/OFF button
●
(3).
Cut only small areas.
●
Move the clipper slowly along hair.
●
Hold the device so, that the comb attachment is laid at.
●
Always start the cutting from the neck upwards or from
●
the forehead and temples upwards to the top of head.
CUTTING HAIR WITHOUT ATTACHMENT
WARNING: The cutting head (1) is very sharp. Injury
hazard!
Cutting without attachment makes possible to trim the
contour, hair line and whiskers as well as neck shaving.
Turn the device so, that the back part was directed
●
upwards.
Place the edge of the cutting head
●
(1) without comb
attachment on desired length of bristle hairline.
Move down the clipper in operation.
●
Cleaning and maintenance
Start the device pressing in ON/OFF button
●
(3).
Always switch off the hair clipper and unplug the adaptor
●
from the mains supply outlet before cleaning and
maintenance.
Remove the comb attachment from the hair clipper.
●
In order to remove cutting head press the cutting head
●
blade (1) forward with your thumb, in order to release it
from the frame (Fig. C).
If necessary, rinse the plastic comb attachments under
●
running water, and then dry them thoroughly.
Remove the remains of hair from the cutting head
●
(1)
with attached cleaning brush (VII).
Insert the protrusion of cutting head
●
(1) back into the
locking hole in the frame of cutting head.
Press gently the cutting head
●
(1) in, until you hear
a clicking sound of locking.
… 28 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Zelmer 39Z017 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info