Bedienungsanleitung Zelmer 619 (Seite 91 von 92) (Englisch, Polnisch)

539643

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ATTENTION!!! In case of finding out that the nozzle does not spray the water although the

pump is on, check if the back tank is properly assembled (push it strong in),

and assembling the stub in the valve at the base. In case of difficulties with

fitting lubricate the seating of back tank valve and the stub sealing.

− Clean the carpet so, that you do not step on the cleaned surface during cleaNing or just after.

ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one of the a/m

cleaning agents only.

− After cleaning the part of the carpet make a break and dry it with forward and backward movements

of the nozzle. Repeat the activities until the whole surface of the carpet is dried.

− When spraying is finished switch the pump off and press for a moment the button adjusting the

water flow to the nozzle, to release the pressure.

In case of old or especially difficult stains, damp the place with cleaning agent recommended

by ZELMER S.A., up to the moment the foam appear. Then leave for a while and next suck it

out with the vacuum cleaner.

ATTENTION!!! Do not allow the carpet soaking. It can cause the permanent deformation

(rucking).

PLAIN FLOORS CLEANING

− Fit the brush strip on the nozzle.

− Press the pump on/off button in and switch the vacuum cleaner on (as in case of carpets).

− Press the adjusting button at the hose handle to adjust the

water flow to the nozzle.

ATTENTION!!! In case the spraying nozzle is blocked disassemble the

nozzle from the tube and clean (blow) the duct, or replace

the nozzle with a new one.

The set of spare nozzles is attached to the accessories

Nozzle exchange

1. Remove the spraying element and the ring ø 5,6 x 1 from the

big (or small) spraying nozzle,

Press the sprayer with your thumb according to the mark on the nozzle housing.

2. Lubricate the new sprayer including the ring and insert it into the nozzle inlet up to the moment

the hooks are locked.

− Move the nozzle along the cleaned surface with forward and back ward movements.

− Stop the spraying after clearing the part of the floor and suck the solution in, making slow

movements of the nozzle in your direction, until all solution is collected from the floor.

− Continua it until all the floor is cleaned and dried.

− When spraying is finished switch the pump off and press for a moment the button adjusting the

water flow to the nozzle, to release the pressure.

If you preformed wet clearing (picking up wet dirtiness) before finishing operation in the final

stage, suck in abort 1–2l of clean water in order to flush the tubes and hose, and then suck in

the air for a while, in order to dry them.

AFTER OPERATION

− Switch the vacuum cleaner off and unplug it from the mains supply outlet.

− Rewind the cord pressing the rewind button. Hold the plug when rewinding, do not

allow the cord to get entangled and the plug to bump the casing.

− Turn the ending of the hose up to the position where the tops

marks on the hose ending and tank cover each other and remove

the hose from the tank.

− Remove the hose stub from the base.

− Press the button and disassemble the tubes.Disassemble the

hose and nozzle similar way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 619 Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info