Bedienungsanleitung Zelmer 819 (Seite 81 von 84) (Englisch, Polnisch)

539645

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

− Be careful to put the cutting of filter partition

shall be fitted on proper insertion of the tank.

− Cover the back tank with the lid, as

show in the figure beside.

− Insert the hose edge into top lid inlet

HOW TO START UP VACUUM CLEANER

− Take the plug and pull the cord out of the casing.

ATTENTION!!! Be careful during pulling the cord out, the yellow mark on the cord show the end

of the cord. Further trials (pulling) can lead to damage the cord.

− Insert the plug to the mains supply receptacle.

− Switch the vacuum cleaner on pressing the on/off button marked with

symbol

− You can adjust the desired suction power for 819.0 vacuum cleaner by

special buttons on the handle:

„

+”increase power,

„–”reduce power

The currently set power level is indicated with one of four control

lamps. After each switching off, the power is reset as maximum,

despite the power set before

− When vacuuming with water filter unit, check the air

recirculation module knob position.

Place the knob in sucking position.

89BOPERATIONAL INSTRUCTIONS FOR VACUUMING WITH WATER FILTER

− Avoid vacuuming surface covered with foaming enhancing substances. If we can notice through the

tank walls, that the water is very foamy, it is necessary to add anti-foaming agent recommended by

vacuum cleaner manufacturer, i.e. “FOAM-FREE” or “G 478 Entschäumer D”, in amount indicated

on the package. You can buy such agent in ZELMER S.A. network shops or by mail-order.

ATTENTION!!! Vacuuming with exceeding indicated, permitted level of water amount can result

in overflow out of the vacuum cleaner. Such repeated situation can lead to fast

blocking of final filter.

− You should pull carefully the vacuum cleaner across the doorsteps and other rough areas, not to

cause extensive water waving inside the tank. It can cause splitting small amount of water out.

− During long or very intensive vacuuming big amount of rubbish, water in the tank, which is the first

stage of filtration, can be completely or in majority absorbed by dry dirtiness. In such case replace it

with fresh and continue vacuuming.

ATTENTION!!! Long term vacuuming with very dirty water can result in early blocking of final

filter (HEPA filter for type 819,*.***S). It can also lead to vacuuming and filtration

efficiency decreasing.

− It is forbidden to pick up the materials and dirtiness, which can be dangerous for people and can

damage the internal elements of the vacuum cleaner, especially:

− flammable, corrosive, malodorous materials, chemicals, etc.

− high temperature materials and liquids,

− materials which are difficult to make damp such as: gypsum, cement, stone dust, flour, etc.

− too big and too sharp objects, which can be blocked inside the tube, hose or air ducts.

− In order to do use blowing, please set the air recirculation module knob in blowing position.

You can use this function for different purposes, especially for:

− blowing leafs out of balcony or patios,

− drying with warm air the inner walls of tubes and hose and other damp objects.

Vacuum cleaner

handle

BlowingSuction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 819 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info