Bedienungsanleitung Zelmer SB1000 (Seite 43 von 44) (Englisch, Polnisch)

538803

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

SB1000-001_v01

Cleaning and maintenance

Clean the appliance immediately after use to

prevent the deposits inside the blender jug.

Pour approx. 750 ml of water into the blender jug

●

(5) and

start the appliance for about 10 seconds by pressing and

holding the “TURBO” button.

Remove the water from the blender jug

●

(5), turn it upside

down and allow it to dry.

Wash the jug

●

(5), lid (7), stopper (9) and blade unit (10)

in warm water with washing-up liquid, if necessary.

Rinse it under the stream of clean, running water, and

●

dry it.

If you left the pitcher for a long time without cleaning and

●

the pieces of mixed ingredients stuck to the inside of the

pitcher, use a nylon brush.

Do not wash the blender jug

●

(5), lid (7), stopper (9),

coffee grinder (12) or blade unit (10) in a dishwasher.

Aggressive cleaning agents may damage the surface of

the accessories.

Wipe the motor unit

●

(1) casing with a soft, damp cloth.

Never immerse the motor unit (1) in water or

any other liquid.

Do not clean the motor unit casing

●

(1) with aggressive

detergents, such as emulsion, milk, paste, etc. They can

remove the graphic symbols.

Never clean the glass blender jug

●

(5) and the grinder

container (13) with coarse sponges.

Dry all elements of the appliance thoroughly after washing.

●

BLADE UNIT ASSEMBLY

Place the sealing ring (11) onto the blade unit ange (10).

Remove the lid (7) from the blender jug (5), pulling the

locked stopper with level indication (9).

Turn the blender jug (5) “upside down”, and put it on

a stable, level surface.

Insert the blade unit (10) into the opening at the bottom

of the blender jug (5).

Hold the blender jug (5) with one hand, and turn the

blade unit anticlockwise with the other hand, until you feel

the resistance.

The twisting direction is shown at the bottom

of the blade unit.

BLADE UNIT DISASSEMBLY

Unplug the appliance from the mains socket.

Remove the lid (7) from the blender jug (5) pulling the

locked stopper with level indication (9).

Remove the content of the blender jug (5).

Clean the blender jug (see “Cleaning and Maintenance”).

Turn the blender jug (5) upside down, and put it on a stable,

level surface.

Before chopping, remove the veins, membranes

and fat from the meat, and then chop it into

pieces of approx. 2x2 cm in size.

Put the ingredients into the grinder container.

Do not exceed the maximum content level

indicated on the grinder container.

Put the grinder base (15) with blade unit into the grinder

container (13). Make sure that the grinder base sealing ring

is xed tightly to the narrowing in the grinder container.

Grab the clutch cover, and turn the grinder base with

blade unit anticlockwise, until you feel the resistance.

The twisting direction is shown at the bottom

of the grinder base with blade unit.

Turn the grinder upside down, and mount it onto the

motor unit (1), so that one of the protruding elements in the

grinder lid ts in the cut-out in the motor unit.

Turn the grinder (12) clockwise to lock it in place, until you

feel the resistance. The control panel illumination will go on.

Run the appliance.

We recommend you to use the “TURBO”

programme or set the appliance at the

maximum speed.

Set the lowest speed to obtained the best

results of grinding nuts.

Use the mill to grind one type of product only.

Grinding of various products immediately one

after another without careful washing may

result in diffusion of odour and/or avour from

one product to another one.

The grinder should not be running continuously

for more than 30 seconds. Switch the appliance

off after 30 seconds, and wait another 30

seconds before you run it again.

When the grinding has been nished, switch the

appliance off pressing the ON/OFF button . Unplug the

appliance from the mains socket.

Turn the grinder anticlockwise so that the protruding

element in the grinder lid ts in the cut-out in the motor unit.

Remove the grinder from the motor unit.

Open the grinder, following the instructions set forth in

●

section

, but in a reverse order.

Always wash the grinder container and the base

with blade unit in warm water with washing-up

liquid immediately after use. Wipe the grinder

sealing ring with a damp cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer SB1000 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zelmer SB1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info