Bedienungsanleitung Zelmer Supremo 13Z013 (Seite 99 von 104) (Englisch, Polnisch)

538894

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

99GW13-013_v03

Tip: If you do not have a thermometer, a good indication of reaching

the right temperature is if you cannot keep a hand against the jar for

longer than 3 seconds.

Important: Do not boil the milk.

11. Remove the jug and take the frothing attachment off the steam wand.

After each use, clean the wand in warm water with the addition of

washing-up liquid. Clear all its outlets. Promptly wipe the steam wand

and its end with a clean damp cloth (34) and rinse with a small amount

of steam.

12. Holding the jug in one hand tap it lightly on the table so as to release

air bubbles and then move the jug in a circular motion until milk gets

shiny and there are no bubbles in it. This will help obtain a uniform

texture of milk and froth.

USING THE HOT WATER FUNCTION

The hot water function is perfect for preparing the long black drink

(espresso diluted with hot water), hot chocolate and for ﬁ lling a coffee

plunger or a tea pot.

Warning: Before using the hot water function, check that the milk frothing

attachment has been taken off the steam wand.

1. Fill up the tank (1) (2) (3) (4) (5) with cold water.

2. Turn on the espresso machine (6). The pilot light placed under the

POWER button will illuminate in red. AT the same time, the illumination

around the outer edge of the POWER button will start ﬂ ashing which

indicates that the espresso machine is in the course of reaching the

right operating temperature.

3. Move the steam wand to the side of the appliance and check that the

milk frothing attachment has been taken off the steam wand.

4. When the illumination of the POWER button stops ﬂ ashing and gives

continuous light, it means that the espresso machine is ready for

brewing espresso. At the same time the outer edges around each

of the MANUAL, single espresso

and double espresso

buttons will light up (continuous light).

5. Place a cup or a dish under the steam/hot water wand and activate

the hot water function by turning the regulator knob anticlockwise to

position

(35).

6. The moment the cup or dish has been ﬁ lled with the desired amount

of hot water, close the hot water by turning the regulator knob to

position 0 (36).

7. Take out the cup or dish and leave the steam wand over the drip tray

(37).

PROGRAMMING THE ESPRESSO MACHINE

The espresso machine allows to programme the coffee pouring time

so that it is possible to adapt it to the user’ s individual needs (it mainly

concerns the taste or the intensity of coffee).

Originally, the espresso machine has been programmed for a single

espresso

(60 ml) and a double espresso (120 ml). However,

the use can programme their own settings for the single espresso function

or for the double espresso function by following the instructions

below.

Programming a single espresso

1. Fill up the water tank (1) (2) (3) (4) (5) with cold water.

2. Turn on the espresso machine (6). The pliot light placed below the

POWER button will illuminate in red. At the same time, the illumination

around the edge of the POWER button will start ﬂ ashing indicating

that the espresso machine is in the course of reaching the desired

operating temperature.

3. Prepare the ﬁ lter holder. Choose a ﬁ lter for 1 cup (38) and place it

in the ﬁ lter holder (14). Using the measure provided, place ground

coffee in the ﬁ lter (39). Press the coffee down using the tamper (the

other end of the measure) (40). Do not tamp to hard.

Notice: Check that you do not put too much coffee in the ﬁ lter. Wipe

the rim of the ﬁ lter and remove coffee from it (18).

4. Place the ﬁ lter holder in the brew head of the appliance (41). Next

turn the holder all the way to the right (42).

5. Press the PROGRAM button. All the illuminations apart from the

MANUAL button will come on (43).

6. Place 1 cup directly under the brew head on the drip tray (43).

7. Press the single espresso

button and activate the espresso

pouring process (44).

8. After the single espresso button has been pressed, the illumination

of the MANUAL and double espresso

buttons will go out, and

the illumination around the outer edges of the POWER and the single

espresso

buttons will come on.

9. Pour the coffee to the desired level. The moment the desired level

is reached, press the single espresso

button. It will stop the

coffee pouring process. A double sound signal will be heard which will

indicate a new setting for the single espresso

function that has

been pre-programmed and saved in the memory of the appliance.

The illumination of the PROGRAM button will ﬂ ash.

10. Next the appliance will return to the standby mode.

Programming a double espresso

1. Fill up the water tank (1) 2) (3) (4) (5) with cold water.

2. Turn on the espresso machine (6). The signal light placed below the

POWER button will illuminate in red. At the same time, the illumination

around the edge of the POWER button will start ﬂ ashing indicating

that the espresso machine is in the course of reaching the desired

operating temperature.

3. Prepare the ﬁ lter holder. Choose a ﬁ lter for 2 cups (38) and place it

in the ﬁ lter holder (14). Using the measure provided, place ground

coffee in the ﬁ lter (39). Press the coffee down using the tamper (the

other end of the measure) (40). Do not tamp to hard.

Notice: Check that you do not put too much coffee in the ﬁ lter. Wipe

the rim of the ﬁ lter and remove coffee from it (18).

4. Place the ﬁ lter holder in the brew head of the appliance (41). Next

turn the holder all the way to the right (42).

5. Press the PROGRAM button. All the illuminations apart from the

MANUAL button will illuminate (43).

6. Place 2 cups directly under the brew head on the drip tray (43).

7. Press the double espresso

button and activate the espresso

pouring process (45).

8. After the double espresso

button has been pressed, the

illumination of the MANUAL and the single espresso buttons will

go out, and the illumination around the outer edges of the POWER

and the double espresso buttons will come on.

9. Pour the coffee to the desired level. The moment the desired level

is reached, press the double espresso

button. It will stop the

coffee pouring process. A double sound signal will be heard which will

indicate a new setting for the double espresso function that

has been pre-programmed and saved in the memory of the appliance.

The illumination of the PROGRAM button will ﬂ ash.

10. Next the appliance will return to the standby mode.

Restoring factory settings

To restore factory settings, follow the steps below:

1. Press the PROGRAM button.

2. Press and hold the two buttons: MANUAL and PROGRAM together

for about 5 seconds.

3. After about 5 seconds or after hearing 4 sound signals, the illumination

around the edges of the PROGRAM button will ﬂ ash.

4. Release the MANUAL and PROGRAM buttons. The espresso

machine will restore the factory settings for a single espresso

and

a double espresso .

Zelmer Supremo 13Z013 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info