Bedienungsanleitung Zelmer Syrius (Seite 44 von 50) (Englisch, Polnisch)

539690

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

50 1600-016_v01

Before operation make sure that the SAFBAG bag is installed

in the vacuum cleaner chamber and that inlet lter and the

HEPA outlet lter is installed in the appliance.

Switch on the vacuum cleaner by pressing the “on/off”

button (2).

The vacuum cleaner is equipped with an electronic

power control which allows to gradually adjust the vacuum

cleaner suction power during operation. To adjust the

suction power use the power adjustment buttons (10,12)

– to increase the suction power or – to decrease the

suction power. The suction power setting is indicated by the

appropriate number of lit diodes.

 Thevacuumcleanerisequippedwithapower

level memory function.  When you turn off

thevacuumcleanerusing the ON/OFFbutton

(2), the power level is going to be stored in

memory. After the vacuum cleaner is turned

onnexttime,itisgoingtostartworkingatthe

samepowerlevelithadbeenworkingbeforeit

wasturnedoff.

The suction power may be adjusted during operation.

The recommended settings are:

Setting 1 – vacuuming curtains

Setting 2 – vacuuming upholstery

Setting 3 – cost-effective power

Setting 4 – vacuuming carpets

Setting 5 – vacuuming hard oors and crevices.

 The vacuum cleaner is equipped with the

adjustmentfunctionforLEDbrightnessofthe

powerlevelindicator(11)onthecontrolpanel.

In order to set a demanded LED brightness,

youhavetopressbothofthepoweradjustment

buttons  (10) and  (12), and when still

pressing these buttons turn on the vacuum

cleanerbypressingtheON/OFFbutton(2).The

LEDforpowerlevels1,3,and5turnon,and

the motor stays turned off. Next by pressing

thepoweradjustmentbuttons (10)and

(12)youcanrespectivelyincreaseordecrease

the brightness of power level indicator (11).

After setting a desired LED brightness, it is

necessarytoturnoffthevacuumcleanerusing

the ON/OFF button (2). In this way you leave

theLEDbrightnessadjustmentfunctionmode,

andthesetLEDbrightnesslevelisstored.

The vacuum cleaner type 1600.3 is additionally equipped

with remote suction power control located in the suction hose

handle. It allows to change the suction power without the

necessity to bend down.

In order to use this function, open the battery compartment

in the suction hose handle and insert two 1.5 V AAA type

batteries or two chargeable 1.2 V AAA type batteries.

 Insert the batteries so that the battery pole

market“+”isalwaysdirectedtowardsthelock

ofthecompartmentmarkedwith“+”.

Use only high quality batteries. Battery leakage may

cause damage to the electronic system.

To use the remote control of the suction power press the

appropriate button on the hose handle ( , ):

To increase the suction power by one setting press the –

button.

To decrease the suction power by one setting press the –

button.

Press the button on the hose handle to temporarily

switch off the appliance and to operate in the STANDBY

mode.

To continue vacuuming press the STANDBY button (17) once

again. The appliance will start operating with the previously

set suction power.

 The infrared transmitter and receiver have to

“see”eachotherinorderfortheremotecontrol

systemtoworkproperly.

The vacuum cleaner is equipped with an accessory

compartment. To open the compartment lift the vacuum

cleaner handle and pull the accessory compartment cover

(6) upwards.

The accessories may be attached to the accessory

holder in the suction hose handle. This way they will be

available for use at any time.

The vacuum cleaner is equipped with the “Parksystem”

function. This function allows to temporarily switch off the

vacuum cleaner using the fastening hook of the combination

brush without the necessity to use the on/off button. In order

to do so, during operation insert the fastening hook of the

combination brush in the combination brush fastening (5).

The vacuum cleaner will automatically switch off.

Filter disassembly

Before changing the lters make sure that the vacuum cleaner

is switched off and unplugged from the mains supply.

INLET FILTER

Release the front cover fastening (15) and open the

cover.

Slide the inlet lter (20) from the appliance body.

Insert the new lter making sure that the outer edge of

the lter is located to the inside of the limiting rib.

Close the front cover.

HEPA OUTLET FILTER

The vacuum cleaners are equipped with a HEPA (High

Efciency Particulate Air) H11, H13 outlet lter.

The lters have a high ltration capacity; they are made of

special bers which are able to retain almost all dust particles.

The H11 and H13 classes determine the permeability of

Zelmer Syrius Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info