Bedienungsanleitung Zenec E-GO Core Infotainer (Seite 37 von 40) (Englisch)

729836

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

72 Rev.B 73 Rev.B

DYNAMIC INDICATION OF SEAT HEAT

NOTE

All functions related to the air conditioning are only status indications.

The effective range of functions is depending on the vehicle manufacturer, vehicle type and

vehicle configuration. The ZENEC system supports all listed functions above. Differences from

this information, features or functions cannot be used for claims.

Seat heater

Indication of current seat heating level.

In addition to the digit, the seat heating level will be indicated in

three different colour gradations.

Setting

The seat heating level will be displayed in combination with a

digit.

Function Icon Display Information

Temperature

arrows

Indication of actual air flow:

Frontwindow – Center – Leg room

Temperature

Blue ca. LOW – 20.0 C

Yellow ca. 20.0 – 24.0 C

Red ca. 24.0 – HIGH

Ventilator setting

The digit shows the fan level.

Function Icon Operation

A/C profile N/A Open up the shortlist of the various climate profiles

REMOVAL WORK AND PREPARATION

INSTALLATION NOTES

NOTE

● Make sure that all connectors at the rear of the ZENEC system have sufﬁ cient room and are

not bent.

● Connectors without a retaining mechanism must be additionally secured with insulating tape.

CAUTION

● The installation of the ZENEC system should be carried out by an authorized installer. Speciﬁ c

knowledge and tools are required to do the installation. Incorrect installation can cause damage

to the vehicle and the ZENEC system.

● Correct functioning can only be guaranteed when you use the ZENEC original accessories

included in the kit or those optionally available. The ZENEC system and the original accessories

must under no circumstances be modiﬁ ed or altered in any way. Inappropriate actions can

cause damage to the vehicle and the ZENEC system.

NOTE

● The ZENEC E>GO CORE is equipped with an integrated DAB+ receiver. To make use of this

you will need a suitable DAB antenna mounted to the vehicle (not included in kit) that must be

connected to the ZENEC system.

● If the target vehicle is already equipped with an original DAB antenna, it is still possible to use it

in combination with the ZENEC system.

● Software updates to the ZENEC system are installed with an USB memory device. Therefore

when ﬁ tting the system make sure that the USB connection of the ZENEC system will still be

accessible later (installation of USB extension cable or USB hub).

● If you have questions or problems relating to the ZENEC system, please contact the dealer from

whom it was purchased.

NOTE

1. Remove the ignition key and keep it outside the car until the installation is finished.

2. Please wait for approx. 10 minutes until the CAN bus system is completely shut down,

before you start with the uninstallation of the original device.

3. Start with the uninstallation of the original device.

4. Please switch on the ignition only, when all installation steps are done and the ZENEC

system is completely mounted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zenec E-GO Core Infotainer Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zenec E-GO Core Infotainer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info